M833
INSTRUCTIONS MANUAL
FEATURES
SELECTING FEATURES
SETTING THE TIME AND CALENDAR
CHRONOGRAPH
LAP OPERATION
• Time Telling Mode (Hours, Minutes, Seconds, Date and Day of the
Week)
• Calendar Mode (Month, Date, and Day of the Week)
• (2) 24 Hour Alarms
• Hourly Chime: One ‘Beep’ sound every full Hour
• Chronograph Mode: Hours, Minutes, Seconds, and 1/100 of a sec-
ond with Lap Operation
• Countdown Timer
• Second Time Zone
• 12/24 Hour (Military Time)
• Water Resistant as indicated on the watch
• INSTALITE - Electro Luminescent Display
1. Time Telling Mode displays Hours, Minutes, Seconds, Date, and Day of
the Week.
2. From Time Telling Mode, press and hold ‘C’. Calendar Mode appears
and the Month, Date, and Day of the Week are displayed. Release ‘C’ to
return to Time Telling Mode.
3. From Time Telling Mode, press ‘B’ once. Chronograph appears. Press
‘B’ four times to return to Time Telling Mode.
4. From Time Telling Mode, press ‘B’ twice. Alarm Mode appears. Press ‘B’
three times to return to Time Telling Mode.
5. From Time Telling Mode, press ‘B’ three times. Countdown Timer Mode
appears. Press ‘B’ twice to return to Time Telling Mode.
6. From Time Telling Mode, press ‘B’ four times. Second Time Zone Mode
appears. Press ‘B’ twice to return to Time Telling Mode.
1. From Time Telling Mode, press and hold ‘A’ for two to three seconds.
Seconds flash. Press ‘C’ to zero out the Seconds.
2. Press ‘B’. Hours flash. Press ‘C’ to advance the Hour.
NOTE: Pressing and holding ‘C’ will advance digits rapidly. When 12 Hour
Format is selected, ‘PM’ indicates ‘p.m.’ times; there is no indicator for
‘a.m.’ times.
3. Press ‘B’. Minutes flash. Press ‘C’ to advance the Minute.
4. Press ‘B’. The Month flashes. Press ‘C’ to advance the Month.
5. Press ‘B’. The Date Flashes. Press ‘C’ to advance the Date.
6. Press ‘B’. The Day of the Week flashes. Press ‘C’ to advance the Day of
the Week.
7. Press ‘B’. 24/7 Hour Time Format flashes. Press ‘C’ to select either 12
Hour Time or 24 Hour (Military) Time.
NOTE: ‘PM’ indicates ‘p/m/’ times in 12 Hour Format; there is no indicator
for ‘a.m.’ times. ‘24H’ indicates 24 Hour (Military Time).
8. Press ‘A’ to end set sequences and return to Time Telling Mode.
1. From Time Telling Mode, press ‘B’ to enter Chronograph Mode.
2. Press ‘C’ to start timing.
3. Press ‘C’ again to stop timing.
4. Press ‘A’ to reset to zero.
5. Press ‘B’ to return to Time Telling Mode.
1. While in the Chronograph Mode, press ‘C’ to start timing.
2. Press ‘A’ to measure Laps.
3. Press ‘C’ to stop timing at the end of the event.
4. Press ‘A’ to reveal the final Lap Time.
5. Press ‘A’ again to reset to zero.
5. Press ‘B’ to return to Time Telling Mode.
COUNTDOWN TIMER
1. From Time Telling Mode, press ‘B’ three times to enter the Timer Mode.
2. Press and hold ‘A’ of two or three seconds. Hours flash. Press ‘C’ to
adjust the Hour.
3. Press ‘B’. Minutes flash. Press ‘C’ to advance the Minutes.
4. Press ‘B’. Seconds flash. Press ‘C’ to advance the Seconds.
5. When the Countdown Timer is set, press ‘A’ to end set sequence and
return to Timer Mode.
6. Press ‘C’ to start the Countdown Timer.
7. If desired, press ‘C’ again to stop the Countdown Timer. Press ‘C’ again
to resume the Countdown Timer.
NOTE: The Countdown timing will continue in any mode until ‘C’ is
pressed. When the Timer counts down below three minutes, an alarm
(‘Beep Beep’) will sound when the Seconds Digit is ‘0’ or ‘30’. When the
Timer counts down below ten seconds an alarm (‘Beep’) will sound every
second. When the Tim has expired, the alarm (‘Beep Beep Beep’) will
sound for ten seconds or until ‘A’, ‘B’ or ‘C’ is pressed.
8. Press ‘C’ to stop the Timer.
9. Press ‘B’ to return to Time Telling Mode.
SECOND TIME ZONE
SETTING THE 24 HOUR ALARM
EL LIGHT FEATURE
1. From Time Telling Mode, press ‘B’ four times to enter the Second Time
Zone Mode.
2. Press and hold ‘A’ for two or three seconds. Hours flash. Press ‘C’ to
advance the Hour.
3. Press ‘B’. Minutes flash. Press ‘C’ to adjust the Minutes.
4. Press ‘A’ to end set sequence.
5. Press ‘B’ to return to Time Telling Mode.
NOTE: The Second Time Zone (Dual Time) Clock may be used to keep
track of a foreign time.
1. From Time Telling Mode, press ‘B’ twice to enter the Alarm Mode
2. Press and hold ‘ A’. Alarm Hours flash. Press ‘C’ to advance the Alarm
Hour.
3. Press ‘B’. Alarm Minutes flash. Press ‘C ’ to advance the Alarm Minute.
NOTE: Pressing and holding ‘C’ will advance digits rapidly.
4. Press ‘B’. Alarm Number flashes. Press ‘C’ to select either Alarm One
(t1) or Alarm Two (t2).
5. Press ‘A’ to end set sequence.
6. Press ‘B’ to return to Time Telling Mode
1. Press ‘D’ in any mode to illuminate the watch face. The backlight will
remain lit for 2 to 3 seconds.
NOTE: EXCESSIVE USE OF LIGHT WILL SHORTEN BATTERY LIFE.
To Next Page
Need help?
General
