Need help?Do you have a question about the Aruba 2930F 24G 4SFP Plus and is the answer not in the manual?
General| Model | JL253A |
|---|---|
| Switching Capacity | 128 Gbps |
| Forwarding Rate | 95.2 Mpps |
| Operating Temperature | 0°C to 45°C (32°F to 113°F) |
| Storage Temperature | -40°C to 70°C (-40°F to 158°F) |
| Warranty | Limited Lifetime Warranty |
| Ports | 24 x 1GbE, 4 x 1G/10G SFP+ |
| Power Supply | Internal power supply |
| Dimensions | 44.25 x 24.61 x 4.39 cm (17.42 x 9.69 x 1.73 in) |
| Memory and Processor | 4 MB flash |
| Operating Humidity | 15% to 95% non-condensing |
| Storage Humidity | 15% to 95% non-condensing |
| Standards Compliance | IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z, IEEE 802.3ae |
| Management | Web GUI, CLI, SNMP |
| Security | RADIUS, TACACS+, SSL |
| Layer 2 Features | VLAN, STP, RSTP, MSTP, LACP |
| Layer 3 Features | Static routing, RIP |
| QoS | 802.1p, DSCP |
| MTBF | 1, 000, 000 hours |
Overview of the front panel components and ports of the 2930F switches.
Details the connectors and ports located on the back of the 2930F switches.
Highlights key features and capabilities of the Aruba 2930F switch series.
Lists the components included in the Aruba 2930F switch package.
Step-by-step guide for installing the Aruba 2930F switch.
Important safety and environmental considerations before installing the switch.
Guidelines for preparing the physical location for switch installation.
Procedure to check if the switch performs correctly during its initial self-test.
Explains the meaning of different LED indicators during switch boot-up and operation.
Instructions for physically mounting the Aruba 2930F switch in various locations.
Steps for installing and removing SFP/SFP+ transceivers without powering off the switch.
Procedure for connecting the switch to a power source for operation.
Guidance on connecting a console for switch management tasks.
Settings required for configuring a terminal emulator for console access.
Step-by-step instructions for establishing a direct console connection to the switch.
Details the pin assignments for the console cable's RJ-45 and DB-9 connectors.
Instructions for connecting network cables to the switch ports.
Guidance on connecting network cables to ports with installed transceivers.
Illustrates common network configurations and how the switch is used within them.
Outlines essential configuration steps for basic switch management.
Guide to using the console setup screen for initial switch configuration.
Suggestions for next steps after initial switch configuration.
How to manage the switch remotely using its IP address.
Steps to initiate a Telnet session for remote switch management.
Instructions for accessing the switch via a web browser interface.
Common issues and initial checks for resolving switch problems.
Interpreting LED patterns to diagnose switch operational status and faults.
Overview of built-in capabilities for proactive network management and monitoring.
Methods for testing switch circuitry and operating code for hardware issues.
Procedures to verify the compatibility and performance of twisted-pair network cables.
Tests to confirm network communication between the switch and connected devices.
Steps to test the complete communication path between network devices through the switch.
How to reset the switch to its original factory default settings.
Information on updating the switch's software.
Details physical dimensions and weight of various Aruba 2930F switch models.
Lists AC voltage, maximum current, and frequency range for each switch model.
Provides sound power and sound pressure level data for different Aruba 2930F switch models.
Lists safety standards compliance for electrical and electronic equipment.
Details electromagnetic compatibility standards compliance for the switches.
Outlines IEEE standards and laser safety compliance for network technologies.
Details the required cable types and categories for network connections.
Specifies supported distances for various network technologies and cable types.
Explains the use and installation of mode conditioning patch cords for fiber optics.
Instructions for connecting a mode conditioning patch cord for Gigabit-LX.
Describes pin assignments and Auto-MDIX for twisted-pair Ethernet cables.
Lists general wiring guidelines for twisted-pair and other network cables.
Details wiring for straight-through cables and pin assignments.
Details wiring for crossover cables and pin assignments.
Details wiring for 1000 Mbps straight-through cables and pin assignments.
Lists HPE networking-related websites for information and resources.
Lists general HPE information websites.
Provides contact information and methods for obtaining technical support.
Guides users on how to download software updates and subscribe to alerts.
Explains the process for customer self-repair programs for product parts.
Details remote support availability and benefits for supported devices.
Directs users to resources for product warranty and safety compliance information.
Guides users to regulatory compliance information for the product.
Provides instructions on how to submit feedback for improving documentation.
Information regarding product warranty terms and conditions.
General overview of regulatory compliance information for the product.
Declaration related to hazardous substances in electrical and electronic equipment in Turkey.
Declaration regarding restrictions on hazardous substances in electrical and electronic equipment in Ukraine.
To Next Page
