Assa Abloy 5800 ADAEZ PRO User Manual

Copyright © 2018, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights
reserved. Reproduction in whole or in part without the express written permission of ASSA
ABLOY Accessories and Door Controls Group, Inc. is prohibited.
700002-Rev N 09/18
®
5800 ADAEZ PRO
Installation and Operation Instructions
1 of 50
®
5800 ADAEZ PRO
Installation and
Operating Instructions
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications.
Note
Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate this device. This device complies with part 15 of the FCC Rules. Operation is
subject to the condition that this device does not cause harmful interference.
To obtain the latest manual and template revisions or to view installation and programming videos go to
www.nortondoorcontrols.com. For technical support call 800-438-1951 x6030, option 4.
IMPORTANT INSTALLATION INSTRUCTIONS
READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS
WARNING – To reduce the risk of severe injury or death:
TESTED TO COMPLY WITH
FCC STANDARDS
WARNING: This product can expose you to chemicals including
lead, which is known to the State of California to cause cancer or other
reproductive harm. For more information go to
www.P65warnings.ca.gov/product.

Assa Abloy 5800 ADAEZ PRO Specifications

General

Door Weight	Up to 150 lbs
Door Width	Up to 48 inches
Handing	Non-handed
Adjustable Opening Speed	Yes
Adjustable Closing Speed	Yes
Operating Temperature	32°F to 120°F (0°C to 49°C)
Finish	Aluminum
Compliance	ADA
Activation	Push Button or Access Control

Summary

IMPORTANT INSTALLATION INSTRUCTIONS

Purpose

Precautions

Determining the Correct Operator Application

Determine Mounting Installation Type

Operator And Door Arm Installation Instructions - Push Side Applications

Mounting the Door Arm Pivot Bracket

Step-by-step guide for mounting the door arm pivot bracket.

Securing the Operator Mounting Bracket

Installing the Door Arm Pivot

Procedure for installing and tightening the door arm pivot.

Installing the Operator Mounting Bracket

Steps for determining and drilling for the operator mounting bracket.

Installing the Door Arm

Procedure for positioning and attaching the door arm to the operator.

Applying Door Preload

Threading the door arm end link to create a preload for closing.

Connecting Battery Pack

Connecting the battery pack connector and switching it ON.

Operator And Door Arm Installation Instructions - Pull Side Applications

Template Selection and Placement

Mounting the Door Shoe

Steps for drilling and securing the door arm pivot bracket for pull side.

Installing the Operator Mounting Bracket and Cover

Mounting the operator bracket and cover based on door material and type.

Operator Mounting Bracket Adjustment

Installing the Door Operator

Mounting the door operator onto the operator mounting pins.

Installing Shaft Extension

Adjusting Door Arm Length

Positioning Door Arm

Door Arm Coupling Tightening

Evenly tightening the door arm coupling screws.

Miscellaneous Common Instructions

Installing the Pushbutton Switches

Connecting the Battery Pack

Steps to connect the battery pack to the operator and turn it ON.

Installing the Plug-In Transformer

Instructions for routing transformer wiring and connecting to the operator.

Connecting Transformer to Battery Pack

Adjusting Door Spring Tension

How to adjust the door's spring tension for proper operation.

Programming Instructions

Programming the Operator

Step-by-step guide to program the door operator's functions.

Linking the RF Pushbuttons

Linking a single RF transmitter

Process to link one ADAEZ transmitter to the operator's RF receiver.

Customizing Operator Settings (Optional)

Adjusting Settings with Thumbwheel

Using the thumbwheel to adjust parameters like time and force.

Storing and Exiting Settings

Setting Optional Functions

Enabling/Disabling Optional Functions

Guide to enable or disable features like Power Close, Push and Go.

Troubleshooting

Door Does Not Open Automatically

Steps to resolve issues when the door fails to open automatically.

Can't Initialize RF Buttons

Door Will Not Fully Close