Why is my Avantco Ice Maker too slow in making ice?
If your Avantco Ice Maker is making ice too slowly, several factors could be at play. Ensure the condenser and air filter are clean. High ambient temperatures or poor ventilation around the unit can also slow down ice production; the normal working temperature range is 41-95°F. Water temperature should also be within 41-95°F. Check these elements to optimize ice production.
How to reduce noise of Avantco 194MC35022FA?
If your Avantco Ice Maker is making too much noise, ensure it is placed on a leveled foundation and that the unit itself is properly leveled.
What to do if the display of Avantco 194MC35022FA shows E06 high pressure protection?
If the display of your Avantco Ice Maker shows 'E06 high pressure protection', it indicates an issue with the fan. First, check and correct the high pressure switch wires. Also, check and correct the fan itself.
Why does Avantco 194MC35022FA Ice Maker make ice cubes with poor transparency, too thin or incomplete?
If your Avantco Ice Maker is producing ice cubes that are not transparent, too thin, or incomplete, several factors could be responsible. Ensure that the ice thickness setting is correct. Also, verify that the water supply pressure is within the range of 1.3 bar to 5.5 bar. The water temperature should be within the normal working range of 41-95°F. Additionally, inspect the inlet water valve for proper function. Check the inlet water valve for blockages and ensure there are no water leaks.
Why does Avantco Ice Maker shutdown every 3 minutes after startup?
If your Avantco Ice Maker shuts down every 3 minutes after startup, it may be due to the ambient temperature being too high. The normal working temperature range for the unit is 41-95°F.
What to do if the display of Avantco 194MC35022FA shows E04 high temperature?
If the display of your Avantco Ice Maker shows E04 high temperature, it could be due to a dirty and blocked condenser. Clean the condenser to resolve this issue.
Why is ice defrost abnormal in Avantco Ice Maker?
If your Avantco Ice Maker's ice defrost is abnormal, several factors could be the cause. If the ambient temperature is too low, ensure it is within the normal working range of 41-95°F. Check and correct the defrosting valve if it's not starting normally. If the ice thickness is too thin or too thick, check and correct the ice thickness setting.
What to do if indicator is OFF on Avantco Ice Maker?
If the indicator light on your Avantco Ice Maker is off, check the plug and socket to ensure they are properly connected.
What to do if my Avantco Ice Maker shows E06 high pressure protection?
If your Avantco Ice Maker displays the error code E06 indicating high pressure protection, it could be due to the fan not starting. Verify the fan and correct any issues. Also, check the high pressure switch wires and correct if necessary.
What to do if Avantco Ice Maker display shows E04 high temperature?
If your Avantco Ice Maker displays E04 indicating a high temperature issue, the condenser may be dirty or blocked. Clean the condenser to resolve this. Ensure that high pressure switch wires are properly connected.
Detailed steps for installing the ice machine, including connections and checks.
Guides through startup, self-check, ice making, harvest, and shutdown procedures.
Step-by-step guide for manual cleaning and sanitizing of internal parts.
Details on connecting the drain fitting and tubing according to plumbing codes.
Instructions for electrical connection and assembling the ice machine onto the dispenser.
A checklist for final checks before starting up the dispenser and ice machine.
A table listing common symptoms, causes, and possible fixes for dispenser issues.
Details what is not covered by the warranty, including misuse and improper installation.
General| Ice Type | Half Dice |
|---|---|
| Voltage | 115V |
| Hertz | 60 Hz |
| Phase | 1 |
| Refrigerant | R404A |
| Production | 350 lb |
To Next Page