AVOURY One - Cancelling the Tea Preparation Process; Switching off the Tea Maker

PAGE 12
USE
7. Close the pod compartment again.
The tea maker will automatically
read the preparation parameters
provided by the pod.
8. If necessary, use the –/+
18
/
19
buttons for the lling capacity to set
the desired quantity of water. Select
a lower quantity of water for strong-
er tea and a higher quantity of water
for weaker tea. Each press increases
or decreases the water quantity by
15 ml (max. 210 ml, min. 150 ml). The
standard cup size is 180 ml.
9. If necessary, use the +/–
14
/
15
brewing time buttons to set the
desired brewing time for the tea.
Select a longer brewing time for
stronger tea and a shorter brewing
time for weaker tea. The brewing
time will increase or decrease by
one minute with each press.
10. Press the On/O button to brew
the tea.
The LEDs on the lling capacity
display
17
will switch o one after
another until the tea has been dis-
pensed in full.
The brewing time display
16
shows the remaining brewing time.
After the brewing process, the pod
will be ejected automatically and
the brewing container will be rinsed
to prevent any aroma mixing and
to ensure that you can enjoy the
avours of each type of tea. The
rinsing water runs into the drip tray
and not into the cup.
11. To prepare another cup, open the
pod compartment, remove the seal-
ing lm, and insert a new pod.
Cancelling the tea
preparation process
– Press and hold the On/O
button
9
for approx. 3 seconds
during the brewing process.
The liquid contained in the brewing
container at the time when the pro-
cess is stopped is released into the
cup situated beneath the outlet.
Switching o the tea
maker
– Press and hold the On/O button
9
for approx. 3 seconds.
The tea maker switches into stand-
by mode. After two minutes, the tea
maker automatically switches into
standby mode if you do not press
any buttons.
The brewing time display
shows the remaining brewing time.
The LEDs on the lling capacity
display will switch o one after
another until the tea has been di-
spensed in full.
17
16
7. Close the capsule compartment
again. The tea maker will automati-
cally read the preparation para-
meters provided by the capsule.
8. If necessary, use the – / and
+ / buttons for the lling
capacity to set the desired quantity
of water. Select a lower quantity of
water for stronger tea and a higher
quantity of water for weaker tea.
Each press increases or decreases
the water quantity by 15 ml (max. 210
ml, min. 150 ml). The standard cup
size is 180 ml.
9. If necessary, use the + / and
– / brewing time buttons to
set the desired brewing time for the
tea. Select a longer brewing time for
stronger tea and a shorter brewing
time for weaker tea. The brewing
time will increase or decrease by
one minute with each press.
10. Press the Start-Button / to
brew the tea.
The brewing time display
shows the remaining brewing time.
The LEDs on the lling capacity
display will switch o one after
another until the tea has been
dispensed in full.
After the brewing process, the capsule
will be ejected automatically and the
brewing container will be rinsed to
prevent any aroma mixing and to en-
sure that you can enjoy the avours of
each type of tea. The rinsing water runs
into the drip tray and not into the cup.
14
15
18
19
17
16
9
11. To prepare another cup, open the
capsule compartment, remove the
lid foil, and insert a new capsule.
– Press and hold the Start-Button
/ for approx. 3 seconds during
the brewing process. The liquid
contained in the brewing container at
the time when the process is stopped
is released into the cup situated
beneath the outlet.
Cancelling the tea
preparation process
9
Switching o the tea
maker
– Press and hold the Start-Button
/ for approx. 3 seconds.
The tea maker switches into stand-
by mode. After ten minutes, the tea
maker automatically switches into
standby mode if you do not press
any buttons.
9
EN
PAGE 33