What to do if the Axis Security System midspan does not power up?
If your Axis Security System midspan isn't powering up, try these steps: * Ensure you're using an approved power cord. * Confirm the voltage at the power inlet is between 100 and 240V AC. * Remove and then re-apply power to the device, and observe the indicator lights during the power-up sequence.
Why is the Axis Security System port indicator not lit and the midspan not operating?
If a port indicator on your Axis Security System is unlit and the midspan isn't working, it could be due to several reasons: * The midspan might not have detected a device, meaning the port isn't enabled. Ensure your device is designed for PoE operation. * Verify you're using a standard Category 5/5e/6 straight-wired cable with four pairs. * If there's an external power splitter connected, try replacing it to check if it's functioning correctly. * Make sure the input Ethernet cable is connected to the Data In port. * Confirm the device is connected to the Data & Power port. * Try reconnecting the device to a different midspan. If it works, the original port or RJ45 connection may be faulty. * Check for any shorts in the twisted pair cables or RJ45 connectors.
What to do if the Axis Security System end device operates but there is no data link?
If your Axis Security System end device is operating but there's no data link, consider the following: * Check that the port indicator on the front panel is continuously lit. * If using an external power splitter, replace it with one that is known to be working. * Make sure you are using standard UTP/FTP Category 5 straight (non-crossover) cabling with all four pairs for this link. * Ensure the Ethernet cable length is less than 100 meters from the Ethernet source to the remote terminal. * Try reconnecting the device to a different midspan. A faulty port or RJ45 connection may be the cause.
What to do if the Axis Switch end device operates, but there is no data link?
If your Axis Switch's end device operates but lacks a data link, first, check that the port indicator on the front panel is continuously lit. If you're using an external power splitter, try replacing it. Ensure you're using standard UTP/FTP Category 5 straight cabling with all four pairs, and that the Ethernet cable is less than 100 meters. As a last resort, try reconnecting the device to a different midspan to identify a faulty port or RJ45 connection.
What to do if an Axis Switch port indicator is not lit and the midspan does not operate?
If a port indicator on your Axis Switch isn't lit and the midspan doesn't operate, it could be due to several reasons. First, ensure the device is designed for PoE operation, as the midspan may not detect a non-PoE device. Check that you're using a standard Category 5/5e/6 straight-wired cable with four pairs and that the Ethernet cable is connected to the Data In port and that the device is connected to the Data & Power port. Also, verify there's no short over the twisted pair cables or RJ45 connectors. If using an external power splitter, try replacing it. Finally, test the device on a different midspan to identify a faulty port or RJ45 connection.
How to troubleshoot Axis Switch when midspan does not power up?
If your Axis Switch midspan does not power up, verify that you are using an approved power cord and that the voltage at the power inlet is between 100 and 240V AC. As a next step, remove and re-apply power to the device, then observe the indicators during the power-up sequence.
Covers USA, Europe, Japan, Korea, Canada, Australia compliance for digital devices.
Complies with IEC/EN/UL 60950-1 safety standards for Information Technology Equipment.
Instructions for end-of-life disposal according to local regulations and penalties.
Compliance with European RoHS, Chinese RoHS, and WEEE directives for product disposal.
Details Axis AB's intellectual property rights, patents, and applications.
Information on obtaining technical assistance, downloading documentation, and FAQs.
Disclaimers regarding document accuracy, product liability, and warranty information.
Guidelines for equipment modifications and Axis' policy on specification changes.
Axis Communications AB contact details, address, phone, fax, and website.
Guidelines for transporting, storing, and handling the Axis product safely.
Requirements for power cords, RJ45 ports, and network cable types.
Safety measures for AC power, SELV circuits, voltage matching, and location.
Explains PoE Midspan functionality, 48V DC delivery, and IEEE802.3af standard.
Steps before installation, mounting considerations, and cable length limits.
Step-by-step instructions for connecting the PoE Midspan to power and network.
Diagram of ports and description of LED indicators for status monitoring.
Details operating/storage conditions, input voltage, current, power output, and Ethernet interface.
Provides solutions for power issues, port indicators, and data link problems.
General| Input current | 0.5 A |
|---|---|
| Input voltage | 100 - 240 V |
| Input frequency | 47 - 63 Hz |
| Power over Ethernet (PoE) voltage | - V |
| Ethernet LAN data rates | 10, 100, 1000 Mbit/s |
| Ethernet interface type | Gigabit Ethernet |
| Power over Ethernet (PoE) | Yes |
| Ethernet LAN (RJ-45) ports | 2 |
| Product color | White |
| LED indicators | Fault, Power |
| Harmonized System (HS) code | 85044095 |
Weight and Dimensions| Depth | 140 mm |
|---|---|
| Width | 53 mm |
| Height | 33 mm |
| Weight | 450 g |
| Dimensions (WxDxH) | 53 x 140 x 33 mm |
To Next Page
