Get to know us at: www.axvue.com
Please read the following instrucons and warnings carefully
Keep this instrucon manual for future.
For technical support see FAQ page.
For adult use only.
SETUP & USE
Adapters:
INSTRUCTION MANUAL
Model- E632
Revised at 9/2020
Asphyxiaon Danger: Store this product out of the reach of babies (at least 3 feet away from the
crib). A strap wound around baby’s neck may result in asphyxiaon. Use safety clip to clamp the power
cord and keep it out of baby’s reach. Do not use other extension cords. Only use the power adapter
provided.
- Only use the recommended rechargeable baery. Please contact with us if you need to change it.
For contact list, please refer to the last page of the instrucon.
- Please clean the baery compartment before using.
- Avoid short circuit at power supply terminal.
- Remove the baery when you are not using it or when running out of power.
- Keep baery away from children.
- Dispose the empty baery properly.
- Store this product out of the reach of babies (at least 3 feets (0.9 m) away from the crib). A strap
wound around baby’s neck may result in asphyxiaon. Use safety clip to clamp the power cord and
keep it out of baby’s reach. Do not use other extension cords. Only use the power adapter provided.
- Do not touch the exposed part if the adapter is connected with power.
- Test regularly before inial use or when change the posion of camera.
- Avoid placing the product in humid place or contacng with liquid. (such as bathtub, sink, etc.)
- Do not apply heat to the product.(such as stoves, radiators, etc.)
- Using the product in venlated place. Avoid placing it on sofas, cushions, beds or other places which
may block venlaon.
- The product only can be operated by adult. Do not allow baby to play with it. Tiny accessories are
contained, please be careful when unpack and install it.
THIS PRODUCT CAN NOT SUBSTITUE PARENT’S SUPERVISION ON YOUR CHILD.
WARNING
WARNING
BATTERY WARNING
3 feet
Figure 1
3 feet
Figure 2
Please charge the battery for at least 8 hours
before using the product.
Step 1: Test recepon first, put camera in a suitable
place that will provide you the best view of your baby in
the crib (Note: Do not hang up the camera firmly unl
inial installaon test is completed). Plug adapter into
wall outlet and turn on the camera.
Step 2: Turn on monitor by pressing and holding Power /
Menu buon for 5 seconds unl “axvue” shows up,
then video will show up on the screen immediately. If
video does not show up, please refer to “TO PAIR
MONITOR AND CAMERA (ADD CAMERA)” at next page. If
video shows up, the inial installaon test is completed,
then you can set up the camera according to the
instrucon below.
Set Up Camera: Place camera on a flat surface, such as
wardrobe or shelf (Figure 1). Or hang it on the wall
(Figure 2). No maer wherever to place the camera,
please make sure to keep it away from the crib for at least
3 feet and all power cords should be placed behind the
camera properly. Then adjust the angle of camera lens
unl the enre crib shows up on the display, or adjust it
to the best angle that you think to watch your baby.
FEATURES & COMPONENTS
Camera:
AXVUE E632 Video Baby Monitor
with 5.0'' LCD Screen and Two Cameras
TO USE PORTABLE / BATTERY MODE
Step 1: Charge the baery for at least 8 hours before using portable / baery mode.
Step 2: Make sure the adapter is plugged into camera.
Step 3: The baery life can be up to 10 hours if it is fully charged.
Baery life will be shortened if recharging it connuously. Unplug the power adapter when you are
not using it for a long me.
Please charge the baery for 6
~
8 hours before using the product.
TO USE PLUGGED-IN MODE
Step 1: Place the monitor display in living room, bedroom or any place you want to watch your baby.
Use adapter to connect camera with electrical outlet.
Step 2: Turn on monitor by pressing POWER/MENU buon for 5 seconds unl axvue logo or video
shows up on the screen.
Step 3: Press VIDEO ON/OFF buon to turn off the video if you only need to hear the voice.
Step 4: Turn off the monitor completely by pressing and holding POWER/MENU buon for
5 seconds.
The monitor and camera are paired before shipment. If it is unpaired for some reason, please refer
to the following steps:
TO PAIR MONITOR AND CAMERA (ADD CAMERA)
Step 1: Make sure the camera and monitor are in the same place.
No
Signal
Step 2:
Step 3:
Turn on monitor by pressing
and holding POWER/MENU
buon for 5 seconds.
1. LED*
2. Power / Menu
3. OK / Confirm
4. Zoom
5. Talk Back
6. Video On / Off
7. Up / Volume Up
8. Down / Volume Down
9. Le / Brightness High
10. Right / Brightness Low
11. Microphone
12. Speaker
13. Baery Compartment
14. DC Jack
15. Kickstand
× 3× 1
Monitor:
Power & Low Baery Sound Lights
*LED
1. Lens
2.
Nighme LEDs
3.
Microphone
4. Power On / Off Switch
5. Speaker
6. Temperature Sensor
7. DC Jack
8. Wall mounng hole
× 2
5
Make sure the AC adapter is plugged into
camera and turn on the camera by
pressing Power On / Off Switch “ ”
buon for 5 seconds.
To Next Page
Need help?
General
