Step 1: Place the monitor display in living room, bedroom or any place you want to watch your
baby. Use adapter to connect camera with electrical outlet.
Step 2: Turn on monitor by pressing
Power/Video “ ”
buon for 3 seconds unl
“
KOEHOG
”
logo
or video shows up on the screen.
Step 3: Press
Power/Video “ ”
buon to turn off the video if you only need to hear the voice.
Step 4: Turn off the monitor completely by pressing and holding
Power/Video “ ”
buon for 3
seconds.
Step 1:
Make sure the monitor is at the same area with the camera.
Step 2:
Make sure the camera AC adapters are plugged in.
Step 3:
Press Power/Video “ ” for 5 seconds to power on the monitor.
Step 4:
Press Menu/OK“ ” shortly to enter menu, then press Right “ ” to highlight the
camera opon“ ” funcon and Menu/OK“ ” to confirm.
Step 5:
Using the Le “ ” or Right “ ” to highlight ADD CAM “ ” and press Menu/OK“ ”
to confirm.
Step 6:
Choose the idenfying number to be assigned on the camera.
Step 7:
Press the Menu/OK “ ” buon again to start pairing and the red light will flash.
INSTRUCTION MANUAL
Model- K882
Revised at 4/2021
Get to know us at: www.koehog.com
Please read the following instrucons and warnings carefully
Keep this instrucon manual for the future.
For technical support see the FAQ page.
For adult use only.
1. Power/Video
2. LED
3. Le
4. Talk Back/Zoom
5. Menu/OK
6. Speaker
7. Right
8. Volume Up
9. Volume Down
10. Microphone
11. DC Jack
12. Kickstand
Camera:
1. Power Indicator
2. Lens
3. Nighme LEDs
4. Microphone
5. Temperature Sensor
6. Power On/Off Switch
7. Speaker
8. DC Jack
9. Wall Mounng Hole
Monitor:
Keep the distance between sensor and
body at least 0.6 inch for accurate
temperature result.
0.6 in
Power & Low Baery
Sound Lights
*LED
Adapter:
× 1× 2 × 3
FEATURES & COMPONENTS
-Store this product out of the reach of babies (at least 3 feets (0.9 m)
away from the crib). A strap wound around the baby’s neck may result in
asphyxiaon. Use a safety clip to clamp the power cord and keep it out
of baby’s reach. Do not use other extension cords. Only use the power
adapter provided.
-Do not touch the exposed part if the adapter is connected with power.
-Test regularly before inial use or when change the posion of camera.
-Avoid placing the product in humid place or contacng with liquid. (such as bathtub, sink, etc.)
-Do not apply heat to the product. (such as stoves, radiators, etc.)
-Using the product in venlated place. Avoid placing it on sofas, cushions, beds or other places which
may block venlaon.
-The product only can be operated by adult. Do not allow baby to play with it. Tiny accessories are
contained, please be careful when unpack and install it.
THIS PRODUCT CAN NOT SUBSTITUTE PARENT’S SUPERVISION
ON YOUR CHILD.
WARNING
PLEASE INSTALL THE SUPPLIED RECHARGEABLE
BATTERY INTO THE BATTERY BOX BEFORE USING
THE BABY MONITOR FOR THE FIRST TIME.
Please charge the battery for at least 8 hours before
using the product.
Step 1: Test recepon first, put camera in a suitable place
that will provide you the best view of your baby in the crib
(Note: Do not hang up the camera firmly unl inial
installaon test is completed). Plug adapter into wall outlet
and turn on the camera.
Step 2: Turn on monitor by pressing and holding Power/
Video
“ ” buon for 5 seconds unl “KOEHOG” shows up,
then video will show up on the screen immediately. If video
does not show up, please refer to “TO PAIR MONITOR AND
CAMERA (ADD CAMERA)” at next page. If video shows up,
the inial installaon test is completed, then you can set up
the camera according to the instrucon below.
Set Up Camera: Place camera on a flat surface, such as
wardrobe or shelf (Figure 1). Or hang it on the wall (Figure 2).
No maer wherever to place the camera, please make sure
to keep it away from the crib for at least 3 feet and all power
cords should be placed behind the camera properly. Then
adjust the angle of camera lens unl the enre crib shows up
on the display, or adjust it to the best angle that you think to
watch your baby.
-Only use the recommended rechargeable baery. Please contact us if you need to change it.
For the contact list, please refer to the last page of the instrucon.
-Please clean the baery compartment before using it.
-Avoid short circuits the power supply terminal.
-Remove the baery when you are not using it or when running out of power.
-Keep the baery away from children.
-Dispose of the empty baery properly.
BATTERY WARNING
SETUP & USE
3 feet
3 feet
Figure 1
Figure 2
TO PAIR MONITOR AND CAMERA ( ADD A CAMERA )
Red LED will flash
The monitor and the camera are paired prior to the shipment. If the monitor and
camera are found not paired for some reason, follow steps below:
Step 8:
Press Power/Code
“ ”
on the camera unl the power indicator flashes.
Step 9:
Waing 3 seconds, the green light stop flashing once paired successfully and the video will appear.
VOX
1
1
2
3
4
Step 1: Charge the baery for at least 6 hours before using portable / baery mode.
Step 2: Make sure the adapter is plugged into camera.
Step 3: The baery life can be up to 8 hours if it is fully charged.
Please charge the baery for 6
~
8 hours before using the product.
Baery life will be shortened if recharging it connuously. Unplug the AC adapter when you are
not using it for a long me.
TO USE PORTABLE/BATTERY MODE
TO USE PLUGGED-IN MODE
The SCAN, SELECT, ADD, DELETE, VIEW CAMERA opons are only available when
mulple cameras connected with the monitor. Order extra cameras by vising
us at www.koehog.com or search “Axvue Baby monitor” on Amazon.
Press
KOEHOG K882 Video Baby Monitor
with '' LCD Screen & Two Cameras
To Next Page
Need help?
General
