Axvue E9650W User Manual

Step 4:
OK
vox
OK
13 24
OK
4
5
OK
6
7
OK
1
2
3
OK
Get to know us at: www.axvue.com
Please read the following instrucons and warnings carefully
Keep this instrucon manual for future.
For technical support see FAQ page.
For adult use only.
SETUP & USE
Adapters:
INSTRUCTION MANUAL
Model- E9650W
Revised at 8/2020
Asphyxiaon Danger: Store this product out of the reach of babies (at least 3 feet away from the
crib). A strap wound around baby’s neck may result in asphyxiaon. Use safety clip to clamp the power
cord and keep it out of baby’s reach. Do not use other extension cords. Only use the power adapter
provided.
- Only use the recommended rechargeable baery. Please contact with us if you need to change it.
For contact list, please refer to the last page of the instrucon.
- Please clean the baery compartment before using.
- Avoid short circuit at power supply terminal.
- Remove the baery when you are not using it or when running out of power.
- Keep baery away from children.
- Dispose the empty baery properly.
- Store this product out of the reach of babies (at least 3 feets (0.9 m) away from the crib). A strap
wound around baby’s neck may result in asphyxiaon. Use safety clip to clamp the power cord and
keep it out of baby’s reach. Do not use other extension cords. Only use the power adapter provided.
- Do not touch the exposed part if the adapter is connected with power.
- Test regularly before inial use or when change the posion of camera.
- Avoid placing the product in humid place or contacng with liquid. (such as bathtub, sink, etc.)
- Do not apply heat to the product.(such as stoves, radiators, etc.)
- Using the product in venlated place. Avoid placing it on sofas, cushions, beds or other places which
may block venlaon.
- The product only can be operated by adult. Do not allow baby to play with it. Tiny accessories are
contained, please be careful when unpack and install it.
THIS PRODUCT CAN NOT SUBSTITUE PARENT’S SUPERVISION ON YOUR CHILD.
WARNING
WARNING
BATTERY WARNING
3 feet
Figure 1
3 feet
Figure 2
Please charge the battery for at least 8 hours before
using the product.
Step 1: Test recepon first, put camera in a suitable place that will
provide you the best view of your baby in the crib (Note: Do not
hang up the camera firmly unl inial installaon test is
completed). Plug adapter into wall outlet and turn on the camera.
Step 2: Turn on monitor by pressing and holding Power / Menu
buon for 5 seconds unl “axvue” shows up, then video will show
up on the screen immediately. If video does not show up, please
refer to “TO PAIR MONITOR AND CAMERA (ADD CAMERA)” at
next page. If video shows up, the inial installaon test is
completed, then you can set up the camera according to the
instrucon below.
Set Up Camera: Place camera on a flat surface, such as wardrobe
or shelf (Figure 1). Or hang it on the wall (Figure 2). No maer
wherever to place the camera, please make sure to keep it away
from the crib for at least 3 feet and all power cords should be
placed behind the camera properly. Then adjust the angle of
camera lens unl the enre crib shows up on the display, or adjust
it to the best angle that you think to watch your baby.
FEATURES & COMPONENTS
Camera:
AXVUE E9650W VIDEO BABY MONITOR
with 4.3" LCD Screen and Pan Tilt Camera
TO USE PORTABLE / BATTERY MODE
Step 1: Charge the baery for at least 8 hours before using portable / baery mode.
Step 2: Make sure the adapter is plugged into camera.
Step 3: The baery life can be up to 10 hours if it is fully charged.
Baery life will be shortened if recharging it connuously. Unplug the power adapter when you are
not using it for a long me.
Please charge the baery for 6
~
8 hours before using the product.
TO USE PLUGGED-IN MODE
Step 1: Place the monitor display in living room, bedroom or any place you want to watch your baby.
Use adapter to connect camera with electrical outlet.
Step 2: Turn on monitor by pressing POWER/MENU buon for 5 seconds unl axvue logo or video
shows up on the screen.
Step 3: Press VIDEO ON/OFF buon to turn off the video if you only need to hear the voice.
Step 4: Turn off the monitor completely by pressing and holding POWER/MENU buon for
5 seconds.
The monitor and camera are paired before shipment. If it is unpaired for some reason, please refer
to the following steps:
TO PAIR MONITOR AND CAMERA (ADD CAMERA)
Step 1: Make sure the camera and monitor are in the same place.
No
Signal
Step 2:
Step 3:
Turn on monitor by pressing
and holding POWER/MENU
buon for 5 seconds.
1. LED*
2. Power / Menu
3. Pan / Tilt
4. Volume Up
5. Volume Down
6. Video On / Off
7. To Select a Camera / Up
8. Auto-scan / Down
9. Zoom / Talk Back
10. VOX / Right
11. Microphone
12. Speaker
13. Baery Compartment
14. DC Jack
15. Kickstand
1. Nighme LEDs
2. Lens
3. Nighme LEDs
4. Power Indicator
5. Speaker
6. Power On / Off Switch
7. Temperature Sensor
8. Wall Mounng Hole
9. DC Jack
× 2× 1 × 1
Monitor:
Power & Low Baery Sound Lights
*LED
Keep the camera plugged in and turned "OFF".

Axvue E9650W Specifications

General

Brand	Axvue
Model	E9650W
Category	Baby Monitor
Language	English