EasyManua.ls Logo

B&D PanelPro - User Manual

B&D PanelPro
24 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Doc #: 161041_00
Part #:79151
Released: 04/08/2016
Sectional Door Opener
Instruction Manual
SDO-3V2
Controll-A-Door
®
S
Controll-A-Door
®
S
& PanelPro
®
SDO-4V1
PanelPro
®

Table of Contents

Other manuals for B&D PanelPro

Preview: Installation Instructions
Installation Instructions2 pages

Questions and Answers

  • K
    Kathleen GutierrezAug 18, 2025
    Why doesn't my B&D Door Opening System work from the transmitter?
    • W
      William FosterAug 18, 2025
      If your B&D Door Opening System opener doesn't work from the transmitter, there might be several reasons: * The garage door may be in poor condition (e.g., broken springs). Check the door's operation. * The opener might not have power. Plug a device of similar voltage into the power point to check if it is working. * The transmitter battery might be flat. Replace the battery. * The transmitter may not contain Tri-Tran+TM Technology. Ensure the transmitter has grey buttons and the model number on the back displays V2. * The opener might be in “Vacation Mode.” Turn off “Vacation Mode”. * The transmitter button may not be programmed to operate the door. Code in the transmitter and ensure the correct button is being pressed.
  • A
    andrewdavidsonAug 20, 2025
    What to do if the Close (Red) LED continues to flash on my B&D PanelPro?
    • S
      snownathanAug 20, 2025
      If the close (red) LED continues to flash on your B&D Door Opening System, it indicates that the door is obstructed when closing. Clear away any obstructions and test that the door closes correctly. Alternatively, the limits may be cleared. To resolve this, remove all power sources (including the battery backup), wait until all lights are out (10-15 seconds), then reconnect the power. If the red LED is still flashing, the limits are not set, and you will need to reset them.
  • J
    jeremygardnerAug 22, 2025
    Why is the transmitter range of my B&D PanelPro Door Opening System restricted?
    • A
      Andrew LawsonAug 23, 2025
      If the transmitter range of your B&D Door Opening System varies or is restricted, remember that variations are normal depending on conditions such as temperature or external interference. Ensure you can see the door when using the transmitter. Check the battery status by pressing a button; if it's flashing or there's no light, change the battery. Also, consider the transmitter's position in the vehicle and try aiming it through the windscreen.
  • M
    Monica NelsonAug 26, 2025
    Why does my B&D PanelPro Door Opening System door reverse for no reason?
    • N
      nmaldonadoAug 26, 2025
      If your B&D Door Opening System door reverses for no apparent reason, this may occasionally occur due to environmental conditions like wind, dust, or extreme temperature changes. Make sure the door runs smoothly before increasing the force pressure. Also, if safety beams are installed, they may be partially obstructed. Ensure the beam path is not obstructed and check the alignment.
  • S
    Sarah LoweAug 27, 2025
    Why does the Open (Green) LED continue to flash on my B&D PanelPro?
    • W
      William WalshAug 27, 2025
      If the open (green) LED continues to flash on your B&D Door Opening System, it means the door is obstructed when opening. Clear away any obstructions and test that the door opens correctly.
  • J
    Jeremiah ParkerAug 30, 2025
    What does it mean when the Open (Green) and Close (Red) LEDs are flashing alternatively on my B&D PanelPro Door Opening System?
    • K
      Kelly AndersenAug 30, 2025
      If the Open (Green) LED and Close (Red) LED are flashing alternatively on your B&D Door Opening System, it means that the opener is overloaded. Check the door's operation by disengaging the motor and ensuring the door runs smoothly. If necessary, make door adjustments.
  • V
    victoria63Sep 1, 2025
    What to do if one transmitter works but the others don't on my B&D PanelPro Door Opening System?
    • T
      Timothy ArroyoSep 1, 2025
      If one transmitter works but others don't with your B&D Door Opening System, the cause may be a faulty transmitter. In this case, replace the transmitter. Alternatively, the battery may be flat, so replace the battery.
  • Q
    qthomasSep 4, 2025
    What does it mean when the SERVICE LED is flashing and beeping on my B&D PanelPro?
    • A
      annaholtSep 4, 2025
      If the SERVICE LED has started to flash and is beeping numerous times on your B&D Door Opening System, a fault has been detected. Record the opener function (how many beeps?), then press the SET button once to reset the opener. If the fault continues, contact 13 62 63 for support.
  • J
    James WhitakerSep 6, 2025
    Why does my B&D PanelPro Door Opening System move slowly under battery power?
    • D
      Debra SimonSep 6, 2025
      If your B&D Door Opening System door stops or moves very slowly under battery power (with the optional battery backup accessory), the batteries may have little or no charge. Connect mains power and leave the batteries to charge; it may take 24 to 48 hours for the batteries to reach their maximum charge capacity.
  • K
    Kim RiosSep 9, 2025
    What to do if the chain moves but the door remains stationary on my B&D PanelPro?
    • T
      Terri SmithSep 9, 2025
      If the chain moves but the door remains stationary on your B&D Door Opening System, the opener is disengaged. Re-engage the opener.

Summary

Installation Safety Warnings

Before you Begin

Tools Required

Kit Contents

Position

Fit the Opener

Bracket Position

Alternative Mounting Option

Provides an alternative method for mounting the opener to a structural timber support.

Mounting Brackets and Arms

Connect to Power

Setting the Datum Position

Adjust the Datum

Fine-tunes the opener's position for accurate door operation and limit setting.

Set the Limit Positions

Defines the fully open and fully closed positions for the garage door.

Configuration and Reset Options

Covers resetting limits, factory defaults, and setting the PET mode.

Safety Testing

Auto-Close & Auxiliary

Safety Beams

Essential safety feature to prevent door closing on obstructions.

Auto Close Option

Automatically closes the door after a set time if safety beams are clear.

Auxiliary Output

Enables control of external devices like alarms or other openers.

Coding a Transmitter

Storing the Transmitter Code

Programming remote control transmitters to operate the opener.

Coding a Transmitter to the Courtesy Light

Assigns a transmitter button to control the opener's courtesy light.

Coding a Transmitter Button to Enable Vacation Mode

Sets the opener to respond only to a specific transmitter button.

Coding a Transmitter to enable AUX Output

Assigns a transmitter button to activate the auxiliary output.

Coding a Transmitter

Setting the Transmitter to Operate PET (Pedestrian) Mode

Codes a transmitter button to control the PET mode for partial door opening.

Installation of the Wall Mounted Transmitter

Instructions for mounting and coding a wall-mounted transmitter unit.

Remotely Coding Transmitters

Codes new transmitters using an already programmed transmitter.

Erasing Programmed Codes

Deletes all previously programmed transmitter codes from the opener.

Home Owner Safety Warnings

Opener Safety & Security

Operating your Opener

User Operating Controls

Door Status Indicators

Specifications

Troubleshooting

Troubleshooting

Maintenance

Battery Replacement

Battery Disposal

Service Schedule

Warranty

Optional Accessories

B&D PanelPro Specifications

General IconGeneral
BrandB&D
ModelPanelPro
CategoryDoor Opening System
LanguageEnglish

Related product manuals