Barco DP2K-15C

To Previous Page

Barco NV | Beneluxpark 21, 8500 Kortrijk, Belgium

Registered office: Barco NV | President Kennedypark 35, 8500 Kortrijk, Belgium

www.barco.com

R5905752 /16 | 2021-01-06

Main Page

Table of Contents7
Safety11
General Considerations12
Important Safety Instructions13
Safety Precautions Hazardous Chemicals17
High Brightness Precautions: Hazard Distance17
HD for Fully Enclosed Projection Systems19
HD in Function of Modifying Optics20
General21
Installation Requirements22
Unpacking the Projector24
Initial Inspection26
Installation Process Overview27
Physical Installation29
Positioning the Projector at the Port Window30
Installation of the Exhaust System32
Connecting the Projector with the Power Net33
Power Loop through to the Projector Electronics35
Connecting a UPS with the Projector Electronics37
Lamp & Lamp House39
Introduction40
Removal of the Lamp House41
Removal of the Xenon Lamp42
Installation of the Xenon Lamp46
Installation of the Lamp House51
Resetting the Lamp Parameters53
Realignment of the Lamp in Its Reflector54
Lenses & Lens Holder57
Available Lenses58
Lens Selection58
Lens Installation59
Lens Removal62
Lens Shift, Zoom & Focus62
Scheimpflug Adjustment64
Input & Communication69
Introduction70
Local Keypad70
Integrated Cinema Processor (ICP)71
Integrated Cinema Processor - Direct (ICP-D)72
ICP-D HDMI 2.0 Specifications74
HD-SDI Input Module (Optional)74
Integrated Media Block/Server (Optional)78
Cinema Controller79
Icmp-X83
ICMP-X Introduction85
Icmp-X Hdd87
What Are the Possible HDD Swaps89
Installing a HDD into the ICMP-X90
Removing a HDD from the ICMP-X92
HDD Status Leds93
ICMP-X Status Leds94
ICMP-X Device Certificate95
Obtaining the ICMP-X Certificate97
ICMP-X Configuration Via Communicator98
ICMP-X Communication Ports99
ICMP-X Source Input Ports100
ICMP-X Network Streaming (Live IP) Specifications101
ICMP Displayport Specifications102
ICMP-X SDI Specifications104
ICMP-X HDMI 2.0 Specifications107
ICMP HDMI 1.4 Specifications110
ICMP-X Reset113
Communicator Touch Panel115
Introduction116
Installing the Touch Panel Interface117
Reposition the Touch Panel Interface118
Starting up121
Switching on the DP2K-XXC122
Switching off the DP2K-XXC122
Removal and Installation of Projector Covers123
Removal of the Lamp Cover124
Removal of the Input Cover124
Removal of the125
Removal of the Side Cover126
Removal of the Rear Cover127
Removal of the Top Cover128
Open the Sealed Compartment129
Close the Sealed Compartment130
Installation of the Top Cover131
Installation of the Rear Cover132
Installation of the Side Cover132
Installation of the133
Installation of the Input Cover134
Maintenance135
Removing the Front Dust Filter136
Clean the Dust Filter on the Bottom Side137
Clean the Dust Filter on the Top Side138
Cleaning the Lens139
Cleaning the Exterior of the Projector140
Check Cooling Liquid Level140
Cleaning the UV Blocker of the Lamp House141
Authorization to Clear Security Warning on the Projector142
Convergence143
Convergence Controls144
Preparing the Convergence Adjustment146
Red on Blue Convergence147
Green on Blue Convergence148
A Specifications151
Specifications of a DP2K-12C Projector152
Specifications of a DP2K-15C Projector153
Specifications of a DP2K-20C Projector155
Specifications of the ICMP157
Specifications of the ICMP-X158
Dimensions of the DP2K-XXC159
Center of Gravity of the DP2K-XXC160
Dimensions of the Universal Pedestal161
Technical Regulations161
B Pin Configurations163
About General Purpose Inputs & Outputs (GPIO)164
Pin Configurations of the Communication Ports165
Pin Configurations of the ICMP-X Communication Ports167
Pin Configurations of the Inputs170
C Environmental Information171
Disposal Information172
Turkey Rohs Compliance172
Contact Information173
Production Address173
Download Product Manual173
Glossary175
Index179

Table of Contents

Other manuals for Barco DP2K-15C

Related product manuals