Basler DGC-2020ES User Manual

2-4 9469200995
Configuration through the Front Panel DGC-2020ES
■ DPF REGENRATE SETUP (Visible when ECU is configured for Standard, Volvo Penta, MTU
ADEC, GM/Doosan, Cummins, or MTU Smart Connect.)
□ DPF MANUAL REGEN
□ DPF REGEN DISABLE
■ BATT CHARGER SETUP
□ CHARGER 1 TYPE
□ CHARGER 2 TYPE
■ BATT CHARGR PREALARMS
□ CH1 COMMS FAIL
□ CH1 BATTERY FAIL
□ CH1 CHARGER FAIL
□ CH1 AC OFF
□ CH2 COMMS FAIL
□ CH2 BATTERY FAIL
□ CH2 CHARGER FAIL
□ CH2 AC OFF
■ SENS CHARGR PREALARMS
□ CH1 THERMAL LIMIT (Visible when CHARGER 1 TYPE is set to SENS)
□ CH1 HI DC VOLTS (Visible when CHARGER 1 TYPE is set to SENS)
□ CH1 LOW DC VOLTS (Visible when CHARGER 1 TYPE is set to SENS)
□ CH1 LO CRANK V (Visible when CHARGER 1 TYPE is set to SENS)
□ CH1 INVLD SETTINGS (Visible when CHARGER 1 TYPE is set to SENS)
□ CH1 SNGL UNIT FL (Visible when CHARGER 1 TYPE is set to SENS)
□ CH2 THERMAL LIMIT (Visible when CHARGER 2 TYPE is set to SENS)
□ CH2 HI DC VOLTS (Visible when CHARGER 2 TYPE is set to SENS)
□ CH2 LOW DC VOLTS (Visible when CHARGER 2 TYPE is set to SENS)
□ CH2 LO CRANK V (Visible when CHARGER 2 TYPE is set to SENS)
□ CH2 INVLD SETTINGS (Visible when CHARGER 2 TYPE is set to SENS)
□ CH2 SNGL UNIT FL (Visible when CHARGER 2 TYPE is set to SENS)
■ SPEED SELECT (Visible when ECU is configured for Volvo Penta.)
■ ACCEL POSITION (Visible when ECU is configured for Volvo Penta.)
■ MODULE TYPE (Visible when ECU is configured for MTU MDEC or MTU ECU7/ECU8.)
■ ALIVE MSG (Visible when ECU is configured for MTU MDEC or MTU ECU7/ECU8.)
■ SPEED SETUP
□ J1939 RPM ENABLE (Visible when ECU is configured for Standard, Volvo Penta,
MTU ADEC, GM/Doosan, Cummins, or MTU Smart Connect.)
□ ENGINE RPM
□ SAVE RPM ADJUSTS
□ RPM BAND WIDTH
□ IDLE RPM
□ RPM CHECKSUM
□ SPEED UP (Visible when ECU is configured for MTU ADEC, MTU MDEC 304, MTU
ECU7/ECU8, or MTU Smart Connect.)
□ SPEED DN (Visible when ECU is configured for MTU ADEC, MTU MDEC 304, MTU
ECU7/ECU8, or MTU Smart Connect.)
□ TEST OVRSPEED (Visible when ECU is configured for MTU ADEC, MTU MDEC
304, MTU ECU7/ECU8, or MTU Smart Connect.)
□ SPD DMAND SRC (Visible when ECU is configured for MTU ADEC, MTU MDEC
304, MTU ECU7/ECU8, or MTU Smart Connect.)
□ IDLE REQUEST (Visible when ECU is configured for MTU MDEC 304, MTU
ECU7/ECU8, or MTU Smart Connect.)
□ INCREASE IDLE (Visible when ECU is configured for MTU MDEC 304, or MTU
ECU7/ECU8.)
■ ECU SETUP (Visible when ECU is configured for MTU ADEC, MTU MDEC 304, MTU
ECU7/ECU8, or MTU Smart Connect.)
□ TRIP RESET (Visible when ECU is configured for MTU MDEC 304, or MTU
ECU7/ECU8.)
□ INT OIL PRIME
□ GOV PRM SW (Visible when ECU is configured for MTU ADEC or MTU Smart
Connect.)
□ ENG STRT PRIME (Visible when ECU is configured for MTU MDEC 304, or MTU
ECU7/ECU8.)
□ FAN OVERRIDE (Visible when ECU is configured for MTU MDEC 304, or MTU
ECU7/ECU8.)

Basler DGC-2020ES Specifications

General

Brand	Basler
Model	DGC-2020ES
Category	Controller
Language	English