Bauer 1772C-B - Operating Instructions; Tool Setup and Blade Changes; Adjusting Depth and Bevel

Page 10 <&(%$*4.8"4,7%H'*#$"&8#I%/7*,#*%4,77%JKLLLKLMMKNOPO1 Item 63634
?@<6AQ RS6;@ACRE D@CEA6E@ET6?6AFS
R/*(,$"83%C8#$('4$"&8#
% ;*,9%$.*%6EAC;6%CDSR;A@EA%?@<6AQ%CE<R;D@ACRE%#*4$"&8%,$%$.*%+*3"88"83%&2%$."#%
5,8',7%"847'9"83%,77%$*\$%'89*(%#'+.*,9"83#%$.*(*"8%+*2&(*%#*$%'/%&(%'#*%&2%$."#%/(&9'4$1
A&&7%?*$%F/
AR%S;6!6EA%?6;CRF?%CEgF;Q%<;RD%@TTCX6EA@G%RS6;@ACRE-%
D,Z*%#'(*%$.,$%$.*%A("33*(%"#%"8%$.*%&22K/&#"$"&8%,89%(*5&Y*%"$#%W,$$*(>%
S,4Z%+*2&(*%/*(2&(5"83%,8>%/(&4*9'(*%"8%$."#%#*4$"&81
AR%S;6!6EA%?6;CRF?%CEgF;Q%<;RD%<GQCEV%<;@VD6EA?-%
X&%8&$%'#*%+7,9*#%5,9*%2(&5%."3.K#/**9%#$**7I%,+(,#"Y*%+7,9*#I%&(%5*$,7K%&(%5,#&8(>K4'$$"83%+7,9*#1%%
A.*%3',(9#%&2%$."#%#,)%,(*%8&$%9*#"38*9%$&%/(&$*4$%,3,"8#$%$.*%2,"7'(*%&2%#'4.%+7,9*#1
W,$$*(>%T.,(3"83
Charge battery before using this tool. Follow instructions included with battery charger.
D&'8$"83%,89%;*5&Y"83%W7,9*
1. Remove Blade Wrench from handle
bracket above motor.
2. Hold down Spindle Lock Button while
removing the Blade Bolt and Washer with
Blade Wrench, turning Bolt TGRT[UC?6.
W7,9*%W&7$%
h%U,#.*(
R'$*(%
<7,83*
C88*(%
<7,83*
?,)%
W7,9*
3. Remove Outer Flange.
4. Use the Lower Guard Handle to raise
the Guard and remove the Blade.
Leave the inner flange in place.
5. Install the new blade, with the directional
arrow on the blade pointing the same as the
directional arrow on the Upper Guard.
6. Place the Outer Flange on the spindle.
7. Hold down Spindle Lock Button and replace
Blade Bolt and Washer with Blade Wrench, turning
Bolt counterclockwise.%%Tighten Bolt securely.
8. Replace Blade Wrench to handle
bracket above motor.
@9='#$"83%X*/$.
1. Set the Base flat against the edge of the workpiece.
2. Raise the Depth Lever to allow the
depth of cut to be adjusted.
3. Use Depth Scale to set depth of cut.
U@;ECEVi A&%(*9'4*%$.*%("#Z%&2%#*("&'#%"8='(>I%
,9='#$%$.*%9*/$.%&2%4'$%$&%='#$%+,(*7>%47*,(%
$.*%)&(Z/"*4*%,89%(*5&Y*%#.,Y"83#1
4. After adjustment, tighten Depth Lever.
U@;ECEVi%A"3.$*8%X*/$.%G*Y*(%+*2&(*%'#*1
@9='#$"83%W*Y*7
1. Loosen Bevel Lock Knob to allow the
angle of cut to be adjusted.
2. Use Bevel Scale to set the desired angle.
3. After adjustment, tighten Bevel Lock Knob.
U@;ECEVi%A"3.$*8%W*Y*7%G&4Z%[8&+%+*2&(*%'#*1