Bay Tek Games TICKET MONSTER

Questions and Answers

M
melissa57Aug 7, 2025
How to troubleshoot no power on Bay Tek Games TICKET MONSTER?
- M
  montesericAug 7, 2025
  If your Bay Tek Games Arcade Game Machine has no power and no lights, here's what you can check: * First, ensure the game is plugged into a working wall outlet. * Next, check the power strip breaker switch or the building circuit breaker and reset it if it has tripped. * Try changing the plug position or replacing the power strip, as it might be faulty. * If the above steps don't work, the cable or power supply might be faulty, in which case you should refer to the 'power supply diagnostic'.
A
Alexander LopezAug 11, 2025
What to do if there is no audio on Bay Tek Games TICKET MONSTER Arcade Game Machines?
- L
  lisaburnsAug 11, 2025
  If you're experiencing no audio on your Bay Tek Games Arcade Game Machines, here's what to check: * First, adjust the volume in the main menu to ensure it's not set too low. * Check the audio cable (AACEAU010) connections from the I/O board to the motherboard to the speakers to make sure there are no loose wires or unplugged speakers. * If the problem persists, consider replacing the I/O board (AACB1900) or the motherboard (AAMB8), as they may be faulty.
H
hoffmanginaAug 20, 2025
How to fix wheel lights not working on Bay Tek Games TICKET MONSTER?
- J
  Jennifer CrawfordAug 20, 2025
  If the wheel lights on your Bay Tek Games Arcade Game Machines are not working, here are a few things to check: * If both sides are out, check the connections from the jumper cable (AACE1620) to the power supply. * Ensure the large POWER IN cable connection with the motherboard is not loose; reseat the connector if necessary. * If one side is out, inspect the cables from the light strip (AACE1622) to the jumper cable (AACE1620) to the power supply. * If some lights are out, replace the light strip (AACE1622). * A faulty light strip (AACE1622) may be the cause, so replace it if needed. * If these steps don't resolve the issue, the power supply might be faulty, refer to the 'power supply diagnostics'.
A
Amber VazquezAug 25, 2025
What to do if not all functions work on Bay Tek Games TICKET MONSTER?
- C
  Christopher JimenezAug 25, 2025
  If your Bay Tek Games Arcade Game Machines plays but some functions don't work, it could be due to several reasons: * If inputs aren't working (no coin-up, buttons don’t work, display reads 'door open'), the I/O serial cable might be unplugged between the I/O board and the motherboard. * If the display doesn't show some screens or there's no audio, the USB software flash drive might be loose or faulty. * If the game freezes or locks up, it could be due to faulty RAM or the motherboard.
M
Micheal GravesAug 29, 2025
Why is the dollar bill acceptor not working on Bay Tek Games TICKET MONSTER?
- Z
  zacharycampbellAug 29, 2025
  If the dollar bill acceptor on your Bay Tek Games Arcade Game Machines isn't working, here's what you can check: * First, ensure the DBA is getting 110 VAC. The acceptor should cycle at power up. If not, check the cable connections to the power strip. Be cautious, as this involves 110 VAC. * If there's dirt or debris in the acceptor slot, run a cleaning card (A5CC9000) through the acceptor. * Make sure the dips on the acceptor are set to 'always enable'. * Check the wiring from the DBA to the I/O board for any pinched, broken, or disconnected wires. Repair or replace the wire (AACE1611) if necessary. * If you suspect DBA problems, refer to the DBA manual.
R
Randy FreySep 2, 2025
How to resolve monitor issues on Bay Tek Games TICKET MONSTER Arcade Game Machines?
- S
  Shane MartinSep 2, 2025
  If you're experiencing monitor issues such as brightness, dimness, or blurriness on your Bay Tek Games Arcade Game Machines, here's what you can try: * Remove the fish head. * Take the monitor out of the wood frame and remove any wood blocks holding the monitor in place. * Use the buttons to adjust the settings.
P
Penny ChangNov 15, 2025
Why Bay Tek Games TICKET MONSTER Arcade Game Machines doesn't coin up?
- A
  Angela HarrisonNov 15, 2025
  If your Bay Tek Games Arcade Game Machines isn't registering coins, here's what you can do: * First, check if one of the coin switches is jammed and un-jam it. Remember, if one switch is closed, the other won’t work. * Check for a short in the coin door harness. Unplug the red spade connector from the door and jump between the white and black wires to simulate a coin up. If needed, replace the harness. * Check the connections of the I/O serial cable between the I/O board and the motherboard, reseating the cables. Replace the I/O serial cable if necessary. * A faulty I/O board (AACB1900) can also cause this issue, so consider replacing it. * Ensure the ticket stack is resting properly on the low ticket switches. Adjust the ticket stack so it holds the switch down. * A faulty lo...