Beckman Coulter Avanti J-30 I User Manual (English)

Questions and Answers:

B
Brian RussellAug 17, 2025
What to do if my Beckman Coulter rotor lid is hard to remove?
- J
  Jordan OconnorAug 18, 2025
  If you're having trouble removing the rotor lid, canister cover, or bucket cover from your Beckman Coulter equipment after centrifugation, it could be due to a vacuum buildup inside the container. Try lifting the vent plug on buckets or canister covers with vents to relieve the vacuum. Alternatively, the threads may be contaminated with dirt, dried lubricant, or metal particles, or they may be insufficiently lubricated. Routinely clean metal threads with a diluted solution of Solution 555 (10 parts water to 1 part detergent), and then lubricate them with Spinkote.
M
Miss Jacqueline Henry PhDAug 20, 2025
Why is my Beckman Coulter bottle leaking (bottles with cap assemblies)?
- H
  hchaseAug 20, 2025
  Leakage in bottles with cap assemblies in Beckman Coulter equipment can occur due to: * Moisture or lubrication on the cap or sealing surface. Ensure the O-ring, plug, and bottle lip are dry and free of lubrication before use. * A damaged or defective O-ring or gasket. Replace the O-ring or gasket. * Insufficiently tightened cap. Tighten the cap securely. * An uneven sealing surface on the bottle. Replace the bottle. * Overfilled tube. If using threaded caps without inserts or O-rings, keep the meniscus lower to prevent leakage.
M
Mark SmithAug 22, 2025
What to do if adapters stick in Beckman Coulter buckets?
- J
  John AndersonAug 22, 2025
  To prevent adapters from sticking in buckets after centrifugation in your Beckman Coulter equipment, apply a thin film of powder, such as talcum powder, to the tube adapter rubber bases after cleaning or as required.
M
marcia96Aug 26, 2025
How to prevent Beckman Coulter tube leakage?
- D
  Daisy CortezAug 26, 2025
  To prevent tube leakage in your Beckman Coulter equipment, ensure that caps are properly seated on tubes and fully tightened. Also, make sure all cap components are thoroughly dry before assembly.
H
hwallsAug 28, 2025
What to do if Beckman Coulter Quick-Seal tubes are leaking?
- C
  Crystal MooreAug 28, 2025
  If Quick-Seal tubes are leaking in your Beckman Coulter equipment, it's likely due to improper sealing. After heat-sealing, gently squeeze the tube to test the seal for leaks. If the tube leaks, reseal it.
T
thompsonericAug 30, 2025
Why is my Beckman Coulter bottle leaking (uncapped bottles)?
- P
  Paula HartmanAug 30, 2025
  If an uncapped bottle is leaking in your Beckman Coulter equipment, it is likely because the bottle is too full. The meniscus must be kept lower to prevent leakage.
D
Denise SmithSep 1, 2025
What to do if Beckman Coulter tubes with snap-on caps are leaking?
- R
  Randall WhiteSep 1, 2025
  If tubes with snap-on caps are leaking in your Beckman Coulter equipment, ensure the tube is not too full; the meniscus must be kept lower to prevent leakage.
A
alex86Sep 6, 2025
Why are my Beckman Coulter tubes collapsing?
- M
  Margaret HartSep 6, 2025
  Tube collapse in Beckman Coulter equipment can occur due to several reasons: * Insufficient thinwall tube volume: The meniscus should be 2 to 3 mm below the tube top to provide adequate tube wall support. * Moisture: Ensure that tubes and tube cavities or buckets are dry before inserting the tubes, as moisture can cause the tube to float and collapse. * Reagent incompatibility: Refer to Chemical Resistances for chemical compatibilities of the tube material and chemicals used. * Excessive speed: Refer to the applicable rotor manual for maximum speeds to ensure tubes are not run above their rated speed.
E
Erin PowersSep 9, 2025
Why are my Beckman Coulter tubes cracking?
- R
  Robin JordanSep 9, 2025
  Cracking in Beckman Coulter tubes can be attributed to: * Low temperature: Tubes may crack or become brittle if used below their lower temperature limit. Before using tubes at other than stated temperature limits, evaluate them under centrifugation conditions. * Aging: Tubes may become brittle with age and use. Dispose of brittle or cracked tubes.

Beckman Coulter Avanti J-30 I Specifications

General

Model	Avanti J-30 I
Maximum Speed	30, 000 rpm
Maximum RCF	100, 000 x g
Control System	Microprocessor-based
Refrigeration System	CFC-free
Type	High Performance Centrifuge
Control Panel	Digital display
Power Requirements	230 V, 50/60 Hz
Temperature Range	-10°C to 40°C