UK UK
62 63
DK DK
FJERNELSE AF SPÆDBARNSINDLÆG
Spædbarnsindlægget (X) kan fjernes, når barnet måler 61 cm (ca. 3 måneder), så
det kan få mere plads. For at fjerne spædbarnsindlægget (X), skal du åbne og fjerne
skulderpuderne.
Fjern spædbarnsindlægget og sæt skulderpuderne tilbage på skulderselerne.
FASTGØRELSE MED Y-FORMET SELESYSTEM
Bemærk! Sørg for, at autostolen er fri for løse genstande og legetøj.
Bemærk! Sørg for, at nakkestøtten er korrekt fastlåst, før du bruger autostolen.
• Løsn skulderselerne (e) ved at trykke på justeringsknappen på den centrale
justeringsanordning (d) og trække begge skulderseler op samtidigt.
• Løsn selespændet ved at trykke hårdt på den røde knap (h). Bemærk! Træk altid
i skulderselen (e) og ikke i skulderpuderne (f).
• Placér barnet i autostolen.
• Placér skulderselerne (e) direkte over barnets skuldre.
Bemærk! Sørg for, at skulderselerne (e) ikke er snoet.
• Placér begge spændetunger (g) sammen og lås dem på plads i bæltespændet (i)
med et hørbart “KLIK”.
• Træk forsigtigt i det midterste justeringsbælte (j) for at stramme skulderselerne (e),
indtil de passer til dit barns krop.
For at sikre dit barns sikkerhed, skal du kontrollere, at:
• autostolen er fastgjort bagudvendt (barnets fødder peger mod ryglænet på
køretøjets sæde).
• autostolen KUN bruges på det forreste passagersæde, hvis bilens airbag er
deaktiveret.
The newborn inlay (x) may be removed
after the baby is 76 cm (approx. 3 months)
to provide more space for the child. To
remove the newborninlay (x) open and
remove the shoulder pads. Then remove the
newborn inlay and place the shoulder pads
back on the shoulder belts.
Note! Ensure that the headrest is correctly locked in place before
using the seat.
09
10
To ensure your baby’s safety, check that:
• Loosen shoulder belts (e) by pressing the adjustment button on
central adjuster (d) and simultaneously pulling both shoulder belts up.
• Undo the belt buckle by pressing red button (h) firmly.
• the infant car seat is secured with the child facing the rear of the car
(the child’s feet point towards the backrest of the infant car seat).
• the infant car seat is only used on the front passenger seat if there is
no front airbag that can impact on the infant car seat.
STRAPPING WITH Y-SHAPED BELT SYSTEM
Note! Ensure that the infant car seat is free from toys and hard objects.
• Loosen shoulder belts (e) by pressing the adjustment button on
central adjuster (d) and simultaneously pulling both shoulder belts up.
• Undo the belt buckle by pressing red button (h) firmly.
Note! Please always pull on shoulder belt (e) and not on belt pads (f).
• Put your child into the child seat.
• Place shoulder belt (e) directly over your child’s shoulders.
Note! Ensure that the infant car seat is free from toys and hard objects.
Note! Please always pull on shoulder belt (e) and not on belt pads (f).
• Put your child into the child seat.
• Place shoulder belt (e) directly over your child’s shoulders.
Note! Ensure that shoulder belts (e) are not twisted.
• Place both buckle tongues together and lock them in place in belt
buckle (i) with an audible “CLICK”.
• Pull cautiously on central adjustment belt (j) in order to tighten
shoulder belts (e) until they fit your child’s body.
CONNECTING THE INFANT CAR SEAT WITH BASE
Before first use
STRAPPING WITH Y-SHAPED BELT SYSTEM
40-87cm Rearward facing ISOFIX+Support leg+shaped belt.
Remove the leg support first, when the base is green, it means the
installation is correct
(x)
Removing the Newborn Inlay
d
e
g
f
e
h
i
j
The newborn inlay (x) may be removed
after the baby is 76 cm (approx. 3 months)
to provide more space for the child. To
remove the newborninlay (x) open and
remove the shoulder pads. Then remove the
newborn inlay and place the shoulder pads
back on the shoulder belts.
Note! Ensure that the headrest is correctly locked in place before
using the seat.
09
10
To ensure your baby’s safety, check that:
• Loosen shoulder belts (e) by pressing the adjustment button on
central adjuster (d) and simultaneously pulling both shoulder belts up.
• Undo the belt buckle by pressing red button (h) firmly.
• the infant car seat is secured with the child facing the rear of the car
(the child’s feet point towards the backrest of the infant car seat).
• the infant car seat is only used on the front passenger seat if there is
no front airbag that can impact on the infant car seat.
STRAPPING WITH Y-SHAPED BELT SYSTEM
Note! Ensure that the infant car seat is free from toys and hard objects.
• Loosen shoulder belts (e) by pressing the adjustment button on
central adjuster (d) and simultaneously pulling both shoulder belts up.
• Undo the belt buckle by pressing red button (h) firmly.
Note! Please always pull on shoulder belt (e) and not on belt pads (f).
• Put your child into the child seat.
• Place shoulder belt (e) directly over your child’s shoulders.
Note! Ensure that the infant car seat is free from toys and hard objects.
Note! Please always pull on shoulder belt (e) and not on belt pads (f).
• Put your child into the child seat.
• Place shoulder belt (e) directly over your child’s shoulders.
Note! Ensure that shoulder belts (e) are not twisted.
• Place both buckle tongues together and lock them in place in belt
buckle (i) with an audible “CLICK”.
• Pull cautiously on central adjustment belt (j) in order to tighten
shoulder belts (e) until they fit your child’s body.
CONNECTING THE INFANT CAR SEAT WITH BASE
Before first use
STRAPPING WITH Y-SHAPED BELT SYSTEM
40-87cm Rearward facing ISOFIX+Support leg+shaped belt.
Remove the leg support first, when the base is green, it means the
installation is correct
(x)
Removing the Newborn Inlay
d
e
g
f
e
h
i
j
To Next Page
Loading...