benchmarkwireline.com
P. O. BOX 850
Fax: 281.342.4848
Phone: 281.342.6415
Simonton,Texas 77476
36220 FM 1093
AM5K User Manual Rev Q Oct 2007 Page 23 of 44
5.0 RECOMMENDED SPARE PARTS
It is recommended that the following list of parts be kept on hand for remote locations.
ITEM P/N SAP P/N DESCRIPTION QTY REF
10 AM5KA067 101392411 ASSY LOAD AXLE 2MV/V EEx nA 1 REPLACES AM5KA013
12 AM5KA066 101392415 ASSY MAG MARK DETECTOR EEx Na 1 REPLACES AMS1A039
13 AM5KA068 101392416 ENCODER HD2.5D-0-SS-1200- EEx nA 1 REPLACES AM5KP161
14 AM5KA058 101392417 ASSY BACKUP MAGNETIC EEx Na 1 REPLACES AM5KA055
22 AM5KM001 101393725 WHEEL MEASURING 2FT 5 SPOKE 2 SEE NOTE 1 BELOW
31 AM5KA137 101393735 ASSY WHEEL GUIDE PLAS 35MM BRG 4 SEE NOTE 2 BELOW
33 AM5KA063 101392449 ASSY WHEEL TENSN SHALLOW GROOVE 1
33 AM5KA073 101393736 ASSY WHEEL TENSN DEEP GROOVE 1 OPTION (HI TENSION)
34 AM5KA164 101393737 ASSY WHEEL TENSN FIXD 35MM BRG 2
35 AM5KA065 101392451 ASSY ROLLER SPOOLNG 2.75" PLAS 4
36 AM5KM073 101392452 COUPLING MOD ENCDR 0.250/0.375 2
51 AMS1P009 101392486 RETAINING PIN (T HANDLE) 1
54 AM5KM157 101393742 BEARING BALL 35MM ID MOD 6
55 AM5KP088 101392479 BEARING LINEAR 30MMID X 40MMOD 8
56 C276P002 101392480 BEARING BALL 20MM FAFNIR 204PP 4
58 AM5KM134 101393747 BEARING BALL 40MM ID MOD 1
59 AM5KP001 101392483 CLAMP TOGGLE PUSH/PULL SST 1
101 AM5KP130 101393769 NOZZLE GREASE FITTNG FLUSH 1
NOTE 1:
Heads manufactured before Nov 2002 required the shaft to be replaced when the
measuring wheels were replaced. All later model heads (SN 5K0229) and after come
with keyed shafts that allow the wheel to be replaced without the shaft.
The P/N for wheel and shaft assembly is AM5KA025 (wheel and shaft without magnets
- Encoder Wheel 1) and AM5KA060 (wheel and shaft with magnets - Encoder Wheel 2).
If these P/Ns are ordered, they will automatically be supplied with the new keyed shafts.
From that point forward, the AM5KM001 (101393725) wheels can be used.
NOTE 2:
Heads manufactured before Feb 2004 did not have greaseable bearings. We have
since created a greaseable version for all 7 wheels. All later model heads (SN 5K0412)
and after come with the greaseable bearings.
The top 4 wheels on both old and new heads are interchangeable with the new
greaseable wheels. The bottom three plastic wheels in the old measuring heads are
different then the wheels in new Measuring heads. The diameter of the wheel shaft is
20mm for the old measuring head and 35mm for the new measuring head.
- The P/N for this wheel assembly with the 20mm shaft is AM5KA139 (101414395)
- The P/N for the 20mm shaft only is AM5KM012 (101414399)
To Next Page
Loading...