BENDIX EC-30 ABS-ATC CONTROLLER User Manual

2
COMPONENTS
The EC-30
™
controller ABS function utilizes the following
components:
- Wheel speed sensors (4 or 6, depending on configuration)
- Electro-pneumatic ABS modulator valves (4)
- Dash mounted tractor ABS warning lamp (relay
controlled)
- Service brake relay valve
- Dash mounted trailer ABS warning lamp (towing vehicles
manufactured after March 1, 2001)
- Blink code activation switch (optional)
The EC-30
™
controller ATC function utilizes the following
additional components:
- ATC modulator - Integral to the ATR (antilock/traction
relay) valve assembly
- Dash mounted ATC active/warning lamp
- Serial communication to engine control module
(interfaces with throttle input and engine torque)
- ATC enable/disable switch
ENCLOSURE
The EC-30
™
controller electronics are contained in a non-
metallic housing and are environmentally protected by a
hard epoxy potting compound. The design of the EC-30
™
controller electronics is robust against radio, electro-
magnetic and environmental interference.
A patented LED (light emitting diode) diagnostic display and
magnetic reset switch are incorporated in the housing for
simple, self-contained diagnostics.
The EC-30
™
controller utilizes a 30-pin and an 18-pin wire
harness to interface with ABS, ATC and vehicle system
components.
EC-30
™
Controller Comparison to EC-16
™
and
EC-17
™
Controllers
The EC-30
™
controller has been designed to replace the
EC-17
™
and the EC-16
™
controllers as the standard Bendix
ABS controller for OEM and aftermarket installations. The
EC-30
™
controller has a black plastic enclosure similar to
the EC-17
™
controller. However, the EC-30
™
controller
utilizes plastic mounting inserts to reduce mounting bolt
corrosion, where the EC-17
™
controller utilizes metal
mounting inserts. The EC-16
™
controller utilizes a totally
metal enclosure.
The EC-30
™
controller ABS warning lamp power-up sequence
has been simplified compared to the EC-17
™
and EC-16
™
controllers.
The EC-30
™
controller ABS warning lamp, at power-up without
faults, will illuminate for 2.5 seconds and then turn off.
The ABS warning lamp for EC-17
™
and EC-16
™
controllers,
at power-up without faults, will illuminate for approximately
8 seconds and flash twice before turning off.
FIGURE 2 - EC-30
™
CONTROLLER WITH ATR VALVE
ATC
Modulator
Connector
ABS / ATC
Assembly
EC-30
™
Controller
ATC
Modulator
(integral)
ATR VALVE
EC-30
™
Controller/Valve Added
Assembly ABS / ATR Function Vehicle
Models Valve Provided Application
CR-30 AR-1
™
Valve None All
CR-30BP AR-2
™
Valve Bobtail Brake Tractors
Proportioning Only
AT-30 ATR-1
™
Valve ATC All
AT-30BP ATR-2
™
Valve ATC & Bobtail Tractors
Brake Proportioning Only
CHART 2 - EC-30
™
CONTROLLER / VALVE ASSEMBLIES
CHART 1 - ECU DIFFERENCES (EC-30
™
, EC-17
™
, EC-16
™
CONTROLLERS)
ECU Enclosure ABS Warning Lamp
Model Power-Up Sequence
EC-30
™
Plastic with Plastic 2.5 seconds on, then off
Controller Mounting Inserts
EC-17
™
Plastic with Metal 8 seconds on, two
Controller Mounting Inserts flashes, then off
EC-16
™
Metal Enclosure 8 seconds on, two
Controller flashes, then off
MOUNTING
ECU Only
The EC-30
™
controller can be bracket mounted to the vehicle
cab or chassis as a stand alone ECU. See figure 1.
Valve Mounted EC-30
™
Controller
The EC-30
™
controller can be assembled on one of four
different valve models. The controller valve assembly is then
mounted in place of the standard service brake relay valve
on the vehicle. An assembly model designation is assigned
when the EC-30
™
controller is mounted on an AR (antilock
relay) valve or an ATR (antilock/traction relay) valve. See
figure 2. Some models include bobtail proportioning and/or
ATC functions. See chart 2.

BENDIX EC-30 ABS-ATC CONTROLLER Specifications

General

Brand	BENDIX
Model	EC-30 ABS-ATC CONTROLLER
Category	Controller
Language	English