EasyManua.ls Logo

BendPak XpR-10AC User Manual

Default Icon
60 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
1
INSTALLATION AND OPERATION MANUAL
SHIPPING DAMAGE CLAIMS
When this equipment is shipped, title passes to the
purchaser upon receipt from the carrier. Consequently,
claims for the material damaged in shipment must be made
by the purchaser against the transportation company at the
time shipment is received.
BE SAFE
Your new lift was designed and built with safety in mind.
However, your overall safety can be increased by proper
training and thoughtful operation on the part of the operator.
DO NOT operate or repair this equipment without reading
this manual and the important safety instructions shown
inside.
1645 Lemonwood Dr.
Santa Paula, CA. 93060, USA
Toll Free 1-800-253-2363
Tel: 1-805-933-9970
Fax: 1-805-933-9160
wwwbendpak.com
Keep this operation manual near the
machine at all times. Make sure that
ALL USERS read this manual.
10,000 POUND CAPACITY
12,000 POUND CAPACITY
15,000 POUND CAPACITY
18,000 POUND CAPACITY
SURFACE MOUNTED
TWO-POST LIFTS
MODELS:
XPR-10C
XPR-10CX
XPR-10AC
XPR-10ACX
XPR-12C
XPR-15C
XPR-18C
VERSION A
PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO
INSTALLATION AND OPERATION. BY PROCEEDING YOU AGREE THAT
YOU FULLY UNDERSTAND AND COMPREHEND THE FULL CONTENTS OF
THIS MANUAL. FORWARD THIS MANUAL TO ALL OPERATORS. FAILURE TO
OPERATE THIS EQUIPMENT AS DIRECTED MAY CAUSE INJURY OR DEATH.
MAN REV F 02-08-11
pn# 5900043
Pulley Pins. top and bottom
Arm Restraint Gears now Adjustable
Foot Guards on Column Base Bolt on
Top Trough Conguration
Lift Head Reinforcing Plates (Washers)
Micro Switch Cover Plate
Arm resistants left and right
Question and Answer IconNeed help?

Do you have a question about the BendPak XpR-10AC and is the answer not in the manual?

BendPak XpR-10AC Specifications

General IconGeneral
Lifting Capacity10, 000 lbs
Overall Width145 inches
Weight1, 950 lbs
Overall Height145 inches
Drive-Thru Clearance106.5 inches
Rise Time45 seconds
Motor2 HP
Voltage220V
Power Supply220V
Power Requirements220V

Summary

Owner's Responsibility

Installer and Operator Protective Equipment

Step 3: Column Preparation

Step 4: Site Layout

Step 5: Installing Powerside Column

Step 8: Mounting Hydraulic Power Unit

Step 10: Installing Hydraulic Lines

Step 11: Routing Equalizer Cables

Step 12: Installing Overhead Micro Switch

Step 14: Installing Lift Arms

Important Leveling Instructions

Important Power-Unit Installation Notes

Safety Label Placement Guidelines

Step 15: Power Unit Hook Up

Post-Installation Check-Off

Step 18: Bleeding Hydraulic System

Step 19: Operation Instructions

Owner/Employer Responsibilities

Key responsibilities for safe lift operation and training.

Lift Operation Safety

While Using Lift

Safety precautions to observe during vehicle lifting operations.

To Lower the Lift

Procedure and safety checks for safely lowering the lift.

To Raise the Lift

Maintenance Instructions

Required Monthly Maintenance

Wire Rope Inspection and Maintenance

Safe Lift Operation

Troubleshooting: Lift Will Not Raise

Troubleshooting: Motor Will Not Run

Troubleshooting: Slow Lowering

Troubleshooting: Loaded Lift Won't Raise

Troubleshooting: Lift Will Not Stay Up

Related product manuals