What to do if my Binder KB 240 (E6) Accessories chamber has no function?
If your Binder Accessories chamber isn't working, start by checking the power supply connection and ensuring it's properly connected. Verify that the voltage matches the required 100-120V or 200-240V. Also, inspect the chamber fuse and replace it if necessary. If the fuse blows again, it's recommended to contact Binder service.
Why is my Binder KB 240 (E6) temperature too high with a 'Temp. range' alarm?
If you're getting a 'Temp. range' alarm and the Binder Accessories chamber is overheating, confirm the alarm. The controller might be defective, so contacting Binder service is recommended. Another possible cause is that the controller isn't adjusted correctly, in that case you should calibrate and adjust the controller.
What to do if my Binder KB 240 (E6) shows "Safety controller over- temperature" alarm?
If you receive a "Safety controller over- temperature" alarm on your Binder Accessories, confirm the alarm. Check the temperature set-point and the safety controller set-point. Adjust to a suitable value if needed. Also, consider if there's too much external heat load and reduce it if possible.
What to do if my Binder KB 240 (E6) Accessories shows "Safety controller over- temperature" alarm with safety controller class 3.3?
If your Binder Accessories is showing a "Safety controller over- temperature" alarm with safety controller class 3.3, confirm the alarm. Verify the temperature set-point and the setting of the over-temperature safety controller, adjusting to a suitable limit value if necessary. Also, check for excessive external heat load and reduce it.
What to do if my Binder Accessories has excess temperature and shows "Temp. range" alarm?
If your Binder Accessories displays a "Temp. range" alarm due to excess temperature, confirm the alarm. Ensure the installation site isn't too warm, as an ambient temperature above 25 °C can cause this issue. Select a cooler installation site.
What to do if my Binder KB 240 (E6) temperature is too low, but the notification "Heating active" is on?
If the temperature in your Binder Accessories is too low even though the "Heating active" notification is on, it could be due to a heating defect. In this case, it's best to contact BINDER service for assistance.
Why is my Binder KB 240 (E6) Accessories program duration longer than programmed?
If the program duration on your Binder Accessories is longer than what you've set, it might be due to inappropriate tolerances programmed. For rapid transition phases, avoid programming tolerance limits to allow for maximum heating speed.
What to do if my Binder KB 240 (E6) Accessories temperature is too low and deviates from the set-point?
If your Binder Accessories has a low temperature and triggers a tolerance range alarm, confirm the alarm. Make sure the chamber door is completely closed. If the issue persists, the door gasket might be defective and need replacement. You can also check the controller function, and if necessary, contact BINDER service.
What to do if my Binder Accessories set-point temperature is not reached after specified time?
If the set-point temperature on your Binder Accessories isn't reached after the specified time, make sure the chamber door is completely closed. If the problem continues, the door gasket may be defective and require replacement. You might also need to calibrate and adjust the controller.
Why does my Binder KB 240 (E6) Accessories program stop one section too early?
If your Binder Accessories program stops one section too early, it could be due to an incomplete program line. When programming with the "ramp" setting, define the end value of the desired cycle by adding an additional section with a section time of at least one minute.
Provides essential safety guidelines for installation, operation, and general precautions.
Outlines the specific applications and intended use of the cooling incubators.
Specifies requirements for the installation site and permissible ambient operating conditions.
Details on connecting the chamber to the power supply, including voltage and fuse information.
Detailed guide on creating custom time programs with sections and parameters.
Guide to setting up daily temperature programs for a full week.
Explains the electronic safety controller for over-temperature protection and its modes.
Details the optional advanced safety controller for both over and under temperature protection.
Guidelines for regular maintenance, service requirements, and warranty voidance.
Procedures for cleaning interior and exterior surfaces using recommended agents.
A table detailing common faults, their possible causes, and required corrective measures.
Comprehensive table of technical specifications for all chamber models.
General| Model | KB 240 (E6) |
|---|---|
| Color | Black |
| Capacity | 240 sheets |
| Type | Binder |
| Material | Cardboard |
To Next Page