9 / 20
EN
CHART 6: CONVENTIONAL GUN SET-UPS
TYPE OF FLUID TO BE SPRAYED
COMPLETE
GUN ASSEMBLY
PART NUMBER
FLUID NOZZLE
AND AIR CAP
THIN
5-25 CENTIPOISE
15-19 sec. Zahn 2 cup
wash primers, dyes, stains, solvents, water, inks,
sealers, laquers, lubricants,
zinc chromates, acrylics
3465-10CN-11S0 1.0 mm (.039") X 11C
3465-12CN-11S0 1.2 mm (.047") X 11C
3465-14CN-11S0 1.4 mm (.055") X 11C
3465-16CN-11S0 1.6 mm (.063") X 11C
3465-16CN-12S0 1.6 mm (.063") X 12C
MEDIUM
25-70 CENTIPOISE
20-30 sec. Zahn 2 cup
syntheticenamels,varnishes,shellacs,llers,
primers, epoxies, urethanes, lubricants,
wax emulsions, enamels
3465-12CN-11S0 1.2 mm (.047") X 11C
3465-14CN-11S0 1.4 mm (.055") X 11C
3465-16CN-11S0 1.6 mm (.063") X 11C
3465-16CN-12S0 1.6 mm (.063") X 12C
3465-18CN-11S0 1.8 mm (.070") X 11C
3465-20CN-14S0 2.0 mm (.079") X 14C
3465-22CN-14S0 2.2 mm (.087") X 14C
HEAVY
70-160 CENTIPOISE
31-66 sec. Zahn 2 cup
3465-16CN-11S0 1.6 mm (.063") X 11C
3465-16CN-12S0 1.6 mm (.063") X 12C
3465-18CN-11S0 1.8 mm (.070") X 11C
3465-20CN-14S0 2.0 mm (.079") X 14C
3465-22CN-14S0 2.2 mm (.087") X 14C
ADHESIVES
water based vinyl glues, solvent based neoprenes,
contact cements
3465-20CN-14S0 2.0 mm (.079") X 14C
3465-22CN-14S0 2.2 mm (.087") X 14C
MOLD RELEASE
3465-12CN-11S0 1.2 mm (.047") X 11C
CERAMICS
abrasive materials, glazes, engobes,
porcelain enamel
3465-14CN-14V0 1.4 mm (.055") X 14C n
3465-18CN-14V0 1.8 mm (.070") X 14C n
3465-22CN-14V0 2.2 mm (.087") X 14C n
3465-26CN-14V0 2.6 mm (.102") X 14C n
NON-STICK COATINGS
3465-10CN-11S0 1.0 mm (.039") X 11C
3465-12CN-11S0 1.2 mm (.047") X 11C
HAMMERS
3465-14CN-11S0 1.4 mm (.055") X 11C
3465-16CN-11S0 1.6 mm (.063") X 11C
3465-16CN-12S0 1.6 mm (.063") X 12C
WRINKLE ENAMELS
3465-14CN-11S0 1.4 mm (.055") X 11C
3465-16CN-11S0 1.6 mm (.063") X 11C
ZINC RICH COATINGS
3465-22CN-14V0 2.2 mm (.087") X 14C n
n Tungsten carbide needle and nozzle set-ups ● Plastic needle tip set-ups
BINKS “TROPHY” SERIES AUTOMATIC SPRAY GUN
NEEDLE AND NOZZLE SELECTION GUIDE
To Next Page
Loading...
