17
Fig. Item No. Description
5
6
8
10
14
15
16
17
18
19
20
21
22
24
25
28
30
32
40
41
42
43
44
TRANSMISSION
MOUNTING
ASSEMBLY
117
116
114
113
108
107
106
76
75
74
73
71
70
68
67
66
65
64
59
58
57
56
55
49
48
Fig. Item No. Description
20665 Key, 1/4 x 1/4 x 1-1/8 S.S.
20665-01
Key, 1/4 x 1/4 x 1-3/4 S.S.
O-Ring, 1.25 I.D.
30315
50029
Washer, brass (used up to s/n 499)
Base plate (used up to s/n 499)
63005
14A 63005-1
Base plate (used on s/n 500-on)
63007
Shaft bearing retainer, front
63008
Shaft bearing retainer, rear
(used up to s/n 499)
16A 63008-1
Shaft bearing retainer, rear
(used on s/n 500-on)
63009 Frame side plate
63010
Bowl lock side spacer
63011 Gear box top plate
63014
Auger drive shaft
63015 Main drive shaft
63016 Bearing retainer, main shaft
Spacer, mixer drive shaft63019
63020 Spacer, plastic, mixer drive shaft
25A
63020-1 Spacer, sealed, mixer drive shaft
Mixer drive shaft
63033
63040 72T sprocket #40B72-01
22T sprocket #D40B22
63042
63062
Linkage pivot arm
Linkage arm
63063
63065
Spacer, thrust bearing
63066
Thrust bearing
63067 Spacer, main drive shaft
(used up to s/n 499)
47
(used on s/n 646-on)
63081-01
Bowl support bracket, LH
63081-02
Bowl support bracket, RH
63084
Hopper latch rod
Drive clutch, squire drive
56064
56065
Driving clutch, motor output
56211-1 Engagement lever bushing
56214
Clutch engagement lever, LH
63104 Link engagement handle
56215 Clutch engagement lever, RH
63119
Clutch engagement shaft
56127-1
Woodruff key
MC-21R2
Lock handle groove pin
Shoulder bolt, 3/8-16 x 1/2
SSB50PS
Chain tensioner63126
63127
Tensioner block
63139-01
Bowl lock hook, LH
Bowl lock hook, RH
63139-02
63140 Hopper latch
Bowl adjusting pin63141
Bearing
83017
Bearing
83032
Key, 3/8 x 3/8 x 1-1/2 lg.
83080-07
Pivot arm knob90509
PCM570 V-Ring seal
FW07S
Flat washer, 3/8
Light jam nut, 3/8-16
HN30S
HN35S
Heavy jam nut, 3/8-16
118
119
Set screw, 5/16-18 X 5/16 lg., knurled cup point SSS17KL
SSS20
Set screw, 3/8-16 X 3/8 lg., knurled cup point
120
63063-1
Spring, clutch linkage arm
41A
DescriptionItem No.
20665
Key, ¼ x ¼ x 1⅛”
20665-01
Key, ¼ x ¼ x 1¾”
30315
O-Ring, 1.25 I.D.
50029
Washer, brass (up to s/n: 499)
Fig.
5
6
8
10
63005
Base plate (up to s/n: 499)
63005-1
Base plate (used s/n: 500 on)
63007
Shaft bearing retainer, front
63008
Shaft bearing retainer, rear (up to s/n 499)
14
14A
15
16
63008-1
Shaft bearing retainer, rear (s/n 500 on)
63009
Frame side plate
16A
17
63010
Bowl lock mount spacer, sides
63011
Gear box mount plate, top
63014
Grinder socket shaft
63015-1
Auger drive shaft w/ shoulder
18
19
20
21
63016
Bearing mount, auger drive shaft22
63019
Spacer, mixer drive shaft24
63020
Spacer, mixer drive shaft (up to s/n 645)
63020-1
Spacer, mixer drive shaft (s/n 646 on)
25
25A
63033
Mixer drive shaft
63040
Sprocket, 72 tooth, #40B72-01
63042
Sprocket, 22 tooth, #D40B22
28
30
32
63062
Linkage pivot arm40
63063
Linkage arm41
63063-1
Spring, clutch linkage arm
63065
Spacer, thrust bearing
41A
42
63066
Thrust bearing, auger drive shaft43
63067
Spacer, auger drive shaft44
DescriptionItem No.
63081-01
Bowl support bracket, LH
63081-02
Bowl support bracket, RH
63084
Hold down rod
56064
Driven clutch, square drive
Fig.
47
48
49
55
56065
Driving clutch, motor output
56211-1
Driven clutch engagment lever bushing
56214
Clutch engagement lever, LH
63104
Link engagement handle
56
57
58
59
56215
Clutch engagement lever, RH
63119
Clutch engagement shaft
56127-1
Woodruff key
MC-21R2
Lock handle groove pin
64
65
66
67
SSB50PS
Shoulder bolt, ⅜-16 x ½”
63126
Bracket, chain tensioner
63127
Tension block
63185-01
Bowl lock hook, LH
68
70
71
73
63185-02
Bowl lock hook, RH74
63140
Hopper latch75
63141
Bowl adjusting pin
83017
Bearing, auger drive shaft
76
106
83032
Bearing, mixer shaft
83080-07
Key, ⅜ x ⅜ x 1½”
90509
Plastic ball knob
PCM570
V-Ring seal
107
108
113
114
FW07S
Flat washer, ⅜”116
HN30S
Hex nut, light jam, ⅜-16, SS117
HN31S
Hex nut, ⅜-16, SS
SSS17KL
Set screw, knurled cup point,
5
/
16
-16 x ⅜”
118
119
SSS20
Set screw, knurled cup point, ⅜-16 x ⅜”120
TRANSMISSION
MOUNTING
ASSEMBLY
To Next Page
Loading...
