11
ENGLISH
(Original instructions)
A narrow pencil jet stream distributes the impact of the water
in a concentrated area, resulting in a high impact force on
the cleaning surface. Use a narrow pencil jet stream for deep
cleaning in a concentrated area. However, use it cautiously, as
it may damage some surfaces
Attaching Soap Bottle (Fig. J4)
To connect the soap bottle ( 11 ) to the spray handle ( 4 ),
insert the end of the soap bottle inside the spray handle and
turn the soap bottle counterclockwise to lock it into position.
Note: The wand and soap bottle cannot be installed at the
same time.
Note:The soap bottle should be positioned underneath the
barrel of the spray handle. Do not position the soap bottle
above the barrel of the plastic gun as this will lead to soap
dripping on the barrel.
Spray Tip Application
Spray fan to pencil jet
nozzle
For gentle wide area cleaning.
Turbo Nozzle For abrasive cleaning.
Operation
Warning! To reduce the risk of serious personal injury, turn
unit off and disconnect it from power source before making
any adjustments or removing/installing attachments or acces-
sories. An accidental start-up can cause injury.
Proper Hand Position (Fig. F)
Warning! To reduce the risk of serious personal injury, always
use proper hand position as shown.
Warning! To reduce the risk of serious personal injury, always
hold securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the spray handle
grip ( 5 ) and the other hand on the spray handle ( 4 ) .
Pressure Washing
Preparing Surface for Cleaning
u Remove objects from the area which could create a
hazard such as children's toys or outdoor furniture.
u Insure that all doors and windows are closed tight.
u Protect all plants and trees in the adjacent area with
a drop cloth ensuring that they will not be harmed by
any overspray.
u Pre-rinse cleaning area with fresh water.
u Use only detergents formulated for pressure washers.
u Always test detergent in an inconspicuous area be-
fore use.
Preparing Pressure Washer Unit for Use (K1, K2,
K3, K4)
Danger! Risk of uid injection and laceration. When using the
high-pressure setting, DO NOT allow the high-pressure spray
to come in contact with unprotected skin, eyes, or with any
pets or animals. Serious injury will occur.
Caution! Before operation:
u Connect the garden hose to a water supply. Water can
be drawn from a faucet or another water supply. Refer to
Self Priming under Preparing Pressure Washer Unit
for Use.
u Connect the high pressure hose to the pressure washer
and the spray handle. For instructions on connecting the
high pressure hose to the pressure washer and spray
handle, please refer to Attaching High Pressure Hose
under Assembly.
u Connect the garden hose to the pressure washer. For in-
structions on connecting the water supply to the pressure
washer, please refer to Attaching Garden Hose under
Assembly.
u Plug the power cord into an appropriate power source.
Preparing Spray Handle
Important! Before turning on the pressure washer unit, disen-
gage the trigger lock-off ( 6 ) and squeeze the trigger ( 7 ).
u Disengage the trigger lock-off ( 6 ) .
u Squeeze the trigger ( 7 ). Hold the trigger for 30 seconds
to purge the system of air.
u If air is still found in the water stream, continue to run
water through the spray handle.
Water Connection
Warning! According to the applicable regula-
tions, the appliance must never be used on
the drinking water network without a system
seperator. Use a system seperator as per IEC
61770 Type BA.
Water owing through a system seperator is
not considered drinkable.
u Comply with the regulations of your water supply com-
pany.
u All connecting hoses must have properly sealed joints.
u Make sure the supply hose is at least 12.7 mm in diameter
and is reinforced.
u The appliance should never be used on the drinking water
supply without a backow valve. Water that has passed
the backow valve is considered undrinkable.
Cleaning a Surface
u To start the pressure washer, rotate the ON/OFF dial ( 17 )
to the ON position.
u Conrm that the water faucet is open or use any other
water source so that water will be supplied to the pressure
washer unit.
u The best angle for spraying water against a cleaning
surface is 45 °.
u Spraying head on tends to cause dirt particles to imbed
in the surface.
u When working on vertical surfaces, it is best to apply
detergent starting at the bottom and working upwards
which will prevent the detergent from sliding down and
causing streaks.
u To disengage the spray handle, release the trigger.
NOTE: Excessive pump pressure may be the result of a
clogged nozzle. Always turn OFF the pressure washer unit
To Next Page
Loading...
Need help?
General
