Bosch GCM 216 - Page 23

English | 23
(19)
Mounting holes
(20)
Recessed handles
(21)
Extension bar
(22)
Screw clamp
(23)
Adjustable fence
(24)
Scale for bevel angle
(25)
Angle indicator (vertical)
(26)
Guide roller
(27)
Chip deflector
(28)
Spindle lock
(29)
On/off switch
(30)
On/off switch for laser (cutting line indication)
(31)
Chip ejector
(32)
Hex key
(33)
Clamping handle for various bevel angles
(34)
Transport safety lock
(35)
Holes for screw clamp
(36)
Wing bolt for fixing the guide rail for length gauge
(37)
Guide rail for length gauge
(38)
Securing screw for extension bar
(39)
Hex socket screw for mounting the saw blade
(40)
Clamping flange
(41)
Saw blade
(42)
Inner clamping flange
(43)
Wing bolt for fixing the adjustable fence
(44)
Wing bolt for adjusting the height of the threaded
rod
(45)
Threaded rod
(46)
Clamping screw for length gauge
(47)
Screws for insert plate
(48)
Hex socket screw for fence
(49)
Screw for mitre angle indicator
(50)
Knurled screw for laser protection cap
(51)
Laser lens cover
Technical Data
Mitre sawGCM216
Article number
3601M330..
Rated power inputW1300
No-load speedmin
-1
4800
Laser typenm650
mW<1
Laser class2
Divergence of laser linemrad
(full
angle)
1.0
Mitre sawGCM216
Weight according to EPTA-Pro-
cedure01:2014
kg9.1
Protection class
/ II
Dimensions of suitable saw blades
Saw blade diametermm216
Base blade thicknessmm1.4−1.8
Max. cutting widthmm3.3
Hole diametermm30
Permitted workpiece dimensions (maximum/minimum):(see "Per-
missible workpiece dimensions", page27)
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Only for power tools without starting current limitation: Switching
these on causes the voltage to drop briefly. Other tools may be ad-
versely affected by these if the conditions in the electricity supply are
unfavourable. Malfunctions are not to be expected for system imped-
ances below0.35ohm.
Noise Information
Noise emission values determined according to
EN62841-3-9.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 96dB(A); sound power level
106dB(A). Uncertainty K = 3dB.
Wear hearing protection!
The noise emission value given in these instructions has
been measured in accordance with a standardised measur-
ing procedure and may be used to compare power tools. It
may also be used for a preliminary estimation of noise emis-
sions.
The noise emission value given represents the main applica-
tions of the power tool. However, if the power tool is used
for other applications, with different application tools or is
poorly maintained, the noise emission value may differ. This
may significantly increase noise emissions over the total
working period.
To estimate noise emissions accurately, the times when the
tool is switched off, or when it is running but not actually be-
ing used, should also be taken into account. This may signi-
ficantly reduce noise emissions over the total working
period.
Assembly
u Avoid starting the power tool unintentionally. The
mains plug must not be connected to the power supply
during assembly or when carrying out any kind of
work on the power tool.
Items included
See the list of items included at the start of
the operating manual.
Bosch Power Tools1 609 92A 6DZ | (15.03.2021)