19
Replacing the cooking compartment bulb
Heat-resistant 25 W, 220/240 V bulbs, E14 bulb sockets and
the seals are available from the after-sales service. Please
specify the E number and FD number of your appliance.
: Risk of burns!
Allow the cooking compartment and cooking compartment light
to cool before changing the bulb.
1. Switch off the fuse in the fuse box or unplug at the mains.
2. Turn the cover anti-clockwise to remove.
3. Screw out the bulb by turning it anti-clockwise and replace
with a bulb of the same type.
4. Slide the new seals and the clamping ring onto the glass
cover in the right order.
5. Screw the glass cover with the seals back on again.
6. Connect the appliance to the mains and reset the clock.
Never operate the appliance without the glass cover and seals.
Replacing the glass cover or seals
Any damaged glass cover or seals must be replaced. Please
provide the after-sales service with the E number and FD
number of your appliance.
The appliance is not in operation. A cook-
ing time is shown in the display.
The rotary selector was accidentally oper-
ated
Press the
% button
The
n button was not pressed after mak-
ing the setting
Press the n button or cancel the setting
with the
% button
“Fill water tank” appears even though the
water tank is full
The water tank has not been inserted
properly
Slide in the water tank until it engages.
The detection system is not working Call the after-sales service
“Fill water tank” appears even though the
water tank is not yet empty, or the water
tank is empty but “Fill water tank” does not
appear
The water tank is dirty. The mobile water
level indicators are jammed
Shake and clean the water tank. If the
parts cannot be released, obtain a new
water tank from the after-sales service.
The water tank empties for no discernible
reason. The evaporator dish is overflowing
The water tank was not closed properly Close the lid until you feel it engage.
The tank lid seal is dirty Clean the seal
The seal in the tank cover is defective Obtain a new water tank from the after-
sales service
The evaporator dish has boiled empty
even though the water tank is full.
The water tank has not been inserted
properly
Slide in the water tank until it engages
The feed line is blocked Descale the appliance. Check whether the
water hardness range is set correctly
“Empty tank/Clean?” appears in the dis-
play
The appliance has not been used for at
least two days and the water tank is full
Empty and clean the water tank. Always
empty the water tank after cooking
There is a "pop" noise during cooking Cold/warm effect with frozen food, caused
by the steam
This is normal
When you cook with steam, a lot of steam
is created
The appliance is being automatically cali-
brated
This is normal
When cooking with steam, there is again a
lot of steam
The appliance is unable to calibrate itself
automatically if cooking times are too
short
Restore the appliance to the factory set-
ting (see section: Basic settings). Then
start steaming at 100 °C for 20 minutes
Steam escapes from the ventilation slots
during cooking
This is normal
The appliance is not producing steam
properly
Limescale has formed in the appliance Start the descaling programme.
An “E...” fault message appears in the dis-
play
Technical fault.
Press the
0 button to delete the error
message. Reset the clock if required.
If the error message appears again, call
the after-sales service
The fault message “E011” appears on the
display
A button was pressed for too long or is
jammed
Press the
0 button to clear the fault mes-
sage. Press all of the buttons individually
and check if they are clean
The appliance is not heating. “Demo” is
shown on the display
A button combination was actuated Disconnect the power supply and recon-
nect it after 10 seconds. Within 2 minutes,
press the
D button for 4 seconds
Problem Possible cause Notes/remedy
To Next Page
Loading...
