Bosch HPC 400 User Manual

Calling up information about the system
BOSCH
~ If the standard display is active. press the info key to open
the info menu.
6 Calling up information about the system
The current system values and the active operating conditions
can be displayed easily via the info menu . No changes can be
made in this menu .
~ Turn the selector to select the required menu. e.g. DHW .
~ Press the selector to open the selected menu .
The info menu is adapted to your system automatically . Some
menu items are only available if the system has been set up
accordingly and the user interface has been set correctly
~ Turn the selector to display more avai l able information.
~ Press the Back key to return to the higher menu level.
~ Press and hold the Back key to return to the standard
display .
(7 Chapter 2.1. page 4) .
I
Info
l
....
~
H Heating/Cooling
I
H Consumed energy
l
Hlntemet
I
4' Heating circuit 1 ... 4
I
YHeatpump 1 ... 2
l
Y
IP connection
I
H Operating mode heating/
MTota l
I
H SelVer connection
I
H Set room temp .
I
rtElec . add . heater
I
-{ SW version
I
H Actual room temp.
1
1
)
4 ..
I
HLog indata
I
H Actual flow temp .
I
Compressor
I
MAC address
I
HDHW
I
[{ ...
I
System in formation
I
bSettemp .
H
Output produced
I
H Heat pump status
I
Actual temp.
l
H Total output produced
l
y ..
-{Pool
I
H Hea~ng output produced
J
KStatu s refngerantcircuit
B Pool set point temp .
l
H DHW output produced
l
T.::r Heat pump 1 ... 2
Actual temp. pool H Cooling output produced
I
H Status additional heat
1
-{ Oper.lting data
I
H Pool output produced
1
4'Heatpump 1 ... 2
b
Operating hours Control
HSolar
l
H Elee . add heater output
l
Heat pump 1 ... 2
I
H Solar sensors
I
YHeatpump 1 ... 2
H
Output additional heat HSillary ie ld
l
H Status mixed additional heall
H
Operating hours
I
'-t Solar thermal system
J
b Add . heat source
H Oper.lting hours
1
H Gross-collector area 1
I
MI~ng ~alye
H Operating hours
I
HSolarpump
I
-{ EI . DHW additional heater
HOp . hours for comp o pool
1
H Gross collector area 2
I
I:.f Heat pump 1... 2
H
Number of starts heating
I
H Solarcirc.pump 2
I
H ElectriCity company block
H Number of starts cooling
1
H Reload pump
I
Hpv
I
H
Number of starts DHW
I
y Therm. diSinfec~on pump HSmartgnd
'-t Number of starts pool
I
H Outdoortemp .
1
Actual mode
I
~
~ Outdoor temp. CUIYe I
Outdoortemp .
l
1
1
I
I
I
1
1
~
672081113&102.20
FIg . 5 Menu structure of the mfo menu
1) Only available if a temperature sensor or remote control
is installed in the reference room of the corresponding
heating circuit.
32 HPC400 672082198312017/07)
8 BOSCH
Menu: Heat i ng/Cooling
The menu items in this menu are only available for installed
heating circuits .
Currently valid operating mode in the
selected heating circuit ( Heating . Idle .
Set room temp . The desired room temperature that is
1
Cooling )
current ly valid in the se l ected heating
circuit:
In automatic mode the d esired
room temperature can change
several times a day . if necessary
Permanently constant in optimised
op eration
AdbaI r-.. temp. Currently measured room temperature
in the se l ected heating circuit
Actual flow temp . Currently measured flow temperature
in the se l ected heating circuit
Table 36 Information about the heating
M enu : DHW
This menu is only available if at least one DHW system is
insta ll ed.
Set temp .
Act\A1 temp . Current measured DHW temperature
Table 37 Information about DHW
Menu : Pool
This menu is only available if a heated swimming pool (pool
modu le accessory required) is installed .
Menu item description
Pool set point
temp.
Required water temperature in the
swimming pool
Actual temp . pool Current measured water temperature
in the swimming pool
Table 38 Information regarding the heated swimming pool
Calling up information about the system
Menu : Operating data
Apart from the first menu item. the menu items in this menu are
only available for installed heat pumps. If two heat pumps are
operated in a cascade. all of the menu items are shown
separately for each heat pump apart from the hours run on the
control.
Menu it em description
Operating hours
I Control
Output additional
I Mat
fO;er '- atl- ng - hou - rs
compressor
heat i ng
Operating hours
compressor
cooling
Operating hours
compressor DHW
I Operating hours
compressor pool
Numbe r of surts
heatin e
I Number of starts
cooling
I
Hours run by the control since the heat
pump was commissioned or since the
last reset.
Output of the electric booster hea t er
since commissioning or since the last
reset.
Hours run by the compressor in heating
mode si n ce commission i ng or since the
last reset.
Hours run by the compressor in cooling I
mode since commissioning or since the
last reset.
Hours run by the compressor in DHW
operation since commissioning or
since the last reset.
Hours run by the compressor in po Ol1
operation since commissioning or
since the last reset. --.-J
Number of compressor starts in
heating mode since commiSSioning or
si nce the last reset.
Number of compressorstarts In cooling
mode since commissioning orsince the
last reset.
Number of starts Number of compressor starts in DHW
DHW operation since commissioning or I
since the last r_ es _e_ t. ____ -:-I
Number of starts Number of compressor starts in pool
pool operation since commiSSioning or
since the last reset.
Table 39 Information regarding operating the heat pump
Menu: Consumed energy
In this menu. the cumu l ated amoun ts of energy consumed by
the heat pump and the electric booster heater are displayed as
a total ( Consumed energy > Total ) and separate ly for each
load .
If two heat pumps are operated in a cascade. all of the menu
items are shown separately for each heat pump .
HPC400 b 720821983 (2017/07) 33

Bosch HPC 400 Specifications

General

Brand	Bosch
Model	HPC 400
Category	Control Panel
Language	English