Bose PowerMatch PM8250 User Manual

English User Guide Page 31
pro.Bose.com Installation and Operating Guide
MAIN MENU < UTILITY < ALARM LOG
UTILITY
Standby mode
Alarm Log
Network Setup (Device ID)
Lock Front Panel
Set Front Panel Lock Combination
Display
Restore Factory Settings
Firmware Version
Description This display allows you to view, clear, and erase the last 50 captured alarm notifications.
Available Controls To access ALARM LOG, use the rotary encoder dial from the UTILITY menu to highlight, then press to select.
Navigation Soft Key: Back to UTILITY menu.
Menu Soft Key #5: Enables the rotary encoder dial to scroll through the alarm log.
Menu Soft Key #1: Clears the alarm indicated by the FAULT LED on the front panel.
Menu Soft Key #3: Erases all entries captured in the alarm log. A confirmation screen is presented by which users can confirm (Soft
Key #1) or cancel (Soft Key #5).
Options Clear Alarm, Erase Log, Scroll.
Notes ControlSpace Designer software allows you to configure and view additional information about alarm and fault conditions.
MAIN MENU < UTILITY < NETWORK SETUP (network versions)
UTILITY
Standby mode
Alarm Log
Network Setup (Device ID)
Lock Front Panel
Set Front Panel Lock Combination
Display
Restore Factory Settings
Firmware Version
Description This display allows you to set the network IP address of the amplifier.
Available Controls To access Network Setup, use the rotary encoder dial from the UTILITY menu to highlight, then press to select.
Navigation Soft Key: Back to UTILITY menu.
Menu Soft Key #1: Enables the rotary encoder dial to toggle between DHCP or FIXED IP address mode. Push the rotary encoder
to enable the selection. A confirmation screen is presented by which users can confirm (Soft Key #1) or cancel (Soft Key #5). Upon
confirmation, the unit will save and reboot using the new setting.
Menu Soft Key #2-5: Enables the rotary encoder dial to adjust the value of each IP address octet. Once the IP address has been fully
modified, push the rotary encoder to enable the selection. A confirmation screen is presented by which users can confirm (Soft Key
#1) or cancel (Soft Key #5). Upon confirmation, the unit will save and reboot using the new setting.
Options Mode: DHCP, Fixed
IP Address Octet Values: 0 to 255
Notes DHCP is enabled by default on network version amplifiers. Upon Power Up, resolving of DHCP times out after 10 seconds to IP:80
for PM8500N/PM8250N and IP:40 for PM4500N/PM4250N.
MAIN MENU < UTILITY < DEVICE ID (USB-only versions)
UTILITY
Standby mode
Alarm Log
Network Setup (Device ID)
Lock Front Panel
Set Front Panel Lock Combination
Display
Restore Factory Settings
Firmware Version
Description This display allows you to set the device identification number of the amplifier.
Available Controls To access Device ID Setup, use the rotary encoder dial from the UTILITY menu to highlight, then press to select.
Navigation Soft Key: Back to UTILITY menu.
Rotary Encoder: Use the dial to scroll through device ID values. Push the rotary encoder to set the new device ID. A confirmation
screen is presented by which users can confirm (Soft Key #1) or cancel (Soft Key #5).
Options Device ID Number: 1-255
➞
➞
➞

Bose PowerMatch PM8250 Specifications

General

Damping factor	1000
Amplifier class	D
Audio output channels	- channels
Peak power per channel	- W
Signal-to-Noise Ratio (SNR)	99 dB
Total Harmonic Distortion (THD)	0.4 %
Bridge-mode power output per channel (4 Ohm)	500 W
Purpose	Performance/stage
Equalizer	Yes
Product color	Black
Connectivity technology	Wired
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Speakers connectivity type	-
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %

Weight and Dimensions

Depth	525 mm
Width	483 mm
Height	88 mm
Weight	11100 g