Braun CC4 - Page 31

28
time, finish time, listen and record sources
and the volume.
Select “setting timer” mode (muting is can-
celled)
@ “process” TIMER SET
Select timer program number:
@ “balance+" TIMER TP—
Key in timer program number and select
date (for example) NB:
e*1" EMPTY TP1
afterch 3 s:
D-—.——TP1
or if the memory was already occupied
DAILY TP1 or e.g. D27.01 TP1, use
@ “balance+” to select date
(display: D-——— TP1 or D27.01 TP1. Checking timer
setting
For a daily timer setting, skip the
following 4 commands beginning with D by
pressing
@ “balance+” and enter hours and
minutes at display T-—.~-— ON.
For one-time timer setting within the
current and following month:
key in month (for example)
@"0" D--.0—
e*1" D-~.01
key in day (for example) . Cancelling a timer
@ “2” D2-.01 program
@"2" D22.01
Select switch-on time
@ “balance+” T--—— ON
Key in hours and minutes (for example)
e”1" T= ON
@"4" T14.-— ON
@"4" T14.4—ON
@ "0" T14.40 ON
Select switch-off time Timer operation
@ “balance+” T———— OFF
Key in hours and minutes (for example)
@"" H===O8F
@"5" T15.—— OFF
@ "0" T15.0— OFF
@ "0" T15.00 OFF
Select playback/record sources:
@ “balance+" SRC FM
(FM P1 is-the previous audio source)
It is possible to key in another playback/
record source, for example
@*2" SRC FM P2
Select volume:
@ “balance+” VOL 40
Set volume with
@ “volume+” or “volume-”, e.g. VOL 32
Conclude setting for timer memory
@ “balance+” TIMER SET
To enter further timer program settings,
select the next timer program number with
@ “balance+” TIMER TP—
or end timer entry with
@ “process”, e.g. 94.40 P1
During entry you can return to the preced-
ing group with ,,balance-", and “process”
interrupts the programming at any time.
Invalid entries of data or times will be ignor-
ed. Incomplete or skipped entries e.g. no
on-time and entries of overlapping timer
programs will be displayed as ERROR. The
“balance-” button must be used to return
to the incorrect program step to correct the
entry.
With the CC4 switched on select “setting
timer” by
@ “process” TIMER SET
and
@ “balance+” TIMER TP—
Enter the number of the program to be
checked (for example)
@"4" TIMER TP4.
Step through the program numbers by pres-
sing or continuous pressing on
@ “balance+” until TIMER SET
End timer entry with
@ “process” e.g. 94,40 P1.
With the CC4 switched on, select “setting
timer” by
@ “process” TIMER SET
and
@ “balance+” TIMER TP—
Press the number of the program to be
cancelled for 3 secs (for example)
@ “3” until EMPTY TP3.
End timer entry with
@ “process” e.g. 94.40 Pi.
If at least one timer program has been
entered you can switch the CC4 from
standby mode (display: . ) to timer opera-
tion:
@ “process” TIMER
The CC4 and any cassette deck connected
for recording will be switched on and off at
the preset times. The timer switch on the
cassette deck must be set to “record”.
if the display on the CC4 (in standby mode)
shows TIMER, timer operation must be dis-
abled for normal operation
@ “process”
Remember to switch back to timer opera-
tion after ending normal operation
@ “process” TIMER
If at least one timer program has been
entered and the CC4 is in normal operation
the display TIMER blinks for 60 seconds at
the switch-on time of a timer program
(without interrupting playback).