Broan B110H65RT - User Manual

Broan B110H65RT

24 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

B110H65RT B110H65RS

B130H65RT B130H65RS

B130E65RT B130E65RS

B150H75NT* B150H75NS*

B160H75RT B160H75RS

B160H65RT B160H65RS

B160E65RT B160E65RS

B150E75NT* B150E75NS*

B160E75RT B160E75RS

USER AND INSTALLER MANUAL

INSTALLER: READ THESE INSTRUCTIONS

SAVE THEM FOR USER

RESIDENTIAL USE ONLY

23832 REV. 10

VB0288

*Recirculation mode is not offered on these

models.

Table of Contents

Questions and Answers

V
Valerie MorrisSep 14, 2025
What to do if my Broan B110H65RT displays error E33?
- M
  Madison PorterSep 14, 2025
  If your Broan Fan shows error code E33, try the following steps: 1. Unplug and then plug the unit back in. 2. If the problem persists, remove the core and clear the ventilation wheel of any dirt or obstructions. 3. If the error continues, disconnect J3 (red) and connect a spare blower system. If it works, replace the exhaust blower. 4. If none of these steps work, consider replacing the electronic assembly.
J
jason41Aug 25, 2025
What to do if my Broan B110H65RT displays error E22?
- L
  Leslie FosterAug 25, 2025
  To resolve the E22 error on your Broan Fan, start by visually inspecting the supply damper system. Clean the filters, distribution registers, and the outside supply hood. Also, check the ducting to make sure it's not squeezed or bent. If the problem continues, remove the ducting from the supply path and use the LCD screen to select MAX to see if the unit can reach the selected flow. If it can, review the ducting path. If needed, select the MIN and MAX flow setting values on the LCD screen, then reset the unit. The MAX flow value will then appear on the screen. If the MAX flow is higher than desired, set the MAX and MIN flows. If none of that helps, replace the supply blower and repeat the MIN/MAX flow settings. Finally, if nothing has worked, replace the electronic assembly.
D
David CoxAug 25, 2025
What to do if my Broan B110H65RT Fan shows error E32?
- D
  denisepetersonAug 26, 2025
  To fix the E32 error on your Broan Fan, start with a visual inspection of the exhaust damper system. Ensure you clean the filters, distribution registers, and the outside supply hood. Check the ducting to confirm it is not squeezed or bent. If the issue remains, remove the ducting from the supply path and select MAX on the LCD screen to check if the unit can reach the selected flow. If it can, review the ducting path. If needed, select the MIN and MAX flow setting values on the LCD screen and reset the unit. The MAX flow value will then display. If the MAX flow is above the desired level, set the MAX and MIN flows accordingly. If this doesn't resolve the issue, replace the exhaust blower and repeat setting the MIN/MAX flows. If all else fails, replace the electronic assembly.
A
Amanda MitchellAug 26, 2025
What to do if my Broan Fan displays error W22?
- R
  Ryan CollinsAug 26, 2025
  To resolve the W22 error on your Broan Fan, start by visually inspecting the supply damper system. Clean the filters, distribution registers, and the outside supply hood. Also, check the ducting to make sure it's not squeezed or bent. If the problem continues, remove the ducting from the supply path and use the LCD screen to select MAX to see if the unit can reach the selected flow. If it can, review the ducting path. If needed, select the MIN and MAX flow setting values on the LCD screen, then reset the unit. The MAX flow value will then appear on the screen. If the MAX flow is higher than desired, set the MAX and MIN flows. If none of that helps, replace the supply blower and repeat the MIN/MAX flow settings. Finally, if nothing has worked, replace the electronic assembly.
X
xlutzSep 14, 2025
What to do if my Broan B110H65RT Fan displays error E01?
- W
  wilsonmatthewSep 14, 2025
  If your Broan Fan is showing error code E01: 1. Unplug the unit, inspect the damper system, and remove any obstructions or dirt. Note that you may need to remove filters and the core to access the damper system. Then, plug the unit back in. 2. If the problem persists, open the electrical compartment and check if connector J5 (white) is properly inserted and inspect for any loose wires. 3. If the damper is still not moving, unplug J7 (red) from the electronic assembly and connect the white damper system connector into J7. If the damper moves but the error persists, the electronic assembly must be replaced. Otherwise, replace the damper system.
J
janetbarronSep 23, 2025
What to do if my Broan Fan displays error E42?
- P
  phamseanSep 23, 2025
  If your Broan Fan displays error E42, replace the electronic assembly.
S
steven70Sep 7, 2025
What should I do if my Broan Fan displays error E33?
- J
  Jacqueline MillerSep 7, 2025
  To address error E33 on your Broan Fan, begin by unplugging and plugging the unit back in. If the issue persists, remove the core and clear the ventilation wheel of any dirt or obstacles. If the problem continues, disconnect J3 (red) and connect a spare blower system. If it works, replace the exhaust blower. If these steps do not resolve the issue, replace the electronic assembly.
H
Heather HamptonSep 8, 2025
What does error E34 mean on my Broan B110H65RT Fan, and how can I fix it?
- J
  jasminejordanSep 8, 2025
  To address error E34 on your Broan Fan, start by unplugging the unit and plugging it back in. This error can occur due to under or over voltage detected from severe in-house power supply fluctuation, which stops the motor for protection. If the problem persists after doing this, replace the electronic assembly.
G
grahamchristianSep 23, 2025
How to configure the selection menu on my Broan B110H65RT when it displays error W52?
- B
  Brian HenrySep 23, 2025
  To configure the selection menu on your Broan Fan when error W52 is displayed: 1. Press the + or - buttons to access the selection menu. 2. Complete the configuration.
K
Kimberly SmithAug 31, 2025
How to troubleshoot error E41 on a Broan B110H65RT Fan?
- A
  Andrew TateAug 31, 2025
  To resolve the E41 error on your Broan Fan, first verify that the thermistor is properly connected to connector J7B. If the error continues, disconnect connector J7B and check the resistance of the thermistor connector; it should be within 5 Kohms to 120 Kohms. If the resistance is outside of this range, replace the thermistor. If the problem persists after these steps, replace the electronic assembly.

Broan B110H65RT Specifications

General

Brand	Broan
Model	B110H65RT
Category	Fan
Language	English

Related product manuals

Preview: Broan B150H75NS

Broan B150H75NS

Preview: Broan BP27

Preview: Broan 744

Preview: Broan 750

Preview: Broan 676

Preview: Broan DX90

Preview: Broan 791LED

Preview: Broan QT140LE

Preview: Broan 345SOBK

Preview: Broan SPK110 SPEAKER FAN

Broan SPK110 SPEAKER FAN