Brother DCP-1623W

4-164-16
 Confidential Confidential
 
1.3.101.3.10 Check sCheck sensor operaensor operation (function ction (function code: 32)ode: 32)
<Operating Procedure><Operating Procedure>
(1(1)) NuNumemeriric kec key pay pad mod modedelsls
Press the [3] and [2] buttons in this order in the initial state of maintenance mode.Press the [3] and [2] buttons in this order in the initial state of maintenance mode.
Non-numeric key pad modelsNon-numeric key pad models
PrPresess ths the [e [ ] or ] or [[ ] bu] butttton ton to dio dispsplalay “My “MAIAINTENTENANANCNCE 32E 32” on ” on ththe LCe LCD anD and prd presess ths thee
[OK] button.[OK] button.
(2)(2) The speaThe speaker is tesker is tested by vibrted by vibrating at 40ating at 400Hz and 1000Hz and 100Hz tones reHz tones repeatedlpeatedlyy..
“CVNTPTPH******” and the state of sensors are displayed on the LCD.“CVNTPTPH******” and the state of sensors are displayed on the LCD.
(3)(3) PressinPressing the [g the [StStart] bart] button dutton displaisplays the ys the next inext item.tem.
The table below summarizes the displays on the LCD, sensor names and detectionThe table below summarizes the displays on the LCD, sensor names and detection
status.status.
*1*1
New toner sensor is turned ON or OFF depending on the toner types when the newNew toner sensor is turned ON or OFF depending on the toner types when the new
toner cartridge is set, therefore, distinction between new and used is not described.toner cartridge is set, therefore, distinction between new and used is not described.
*2*2
DCP-16** series, MFC-19** series onlyDCP-16** series, MFC-19** series only
(4)(4) Change tChange the condihe conditions sutions subject to sebject to sensor detnsor detection anection and check thad check that the displt the display on theay on the
LCD changes depending on the sensor status. For example, feed the paper through theLCD changes depending on the sensor status. For example, feed the paper through the
paper feed/paper printing position sensor, create paper jam at the paper exit, or set thepaper feed/paper printing position sensor, create paper jam at the paper exit, or set the
document.document.
(5)(5) When the [SWhen the [Stop/Exitop/Exit] button is pret] button is pressed, thissed, this operatios operation is finishen is finished, and the machid, and the machinene
returns to the initial state of maintenance mode.returns to the initial state of maintenance mode.
Note:Note:
•• Press the [OPress the [OK] button tK] button to stop the tono stop the tone from the spe from the speakereaker..
LLCCDD SSeennssoor r nnaammeess
Detection statusDetection status
(displayed / not displayed)(displayed / not displayed)
CVCV
Top cover sensor, Eject sensorTop cover sensor, Eject sensor
Cover closed, Paper set / Cover Cover closed, Paper set / Cover open, No paperopen, No paper
NTNT
New toNew toner sner sensor, ensor, Toner Toner detection detection sensorsensor Toner Toner set / set / No toNo tonerner
*1*1
PTPT
PPaappeer r ffeeeed d sseennssoorr NNo o ppaappeer r / / PPaappeer r sseett
PHPH
PPaappeer r pprriinnttiinng g ppoossiittiioon n sseennssoorr NNo o ppaappeer r / / PPaappeer r sseett
3030
Internal temperature thermistorInternal temperature thermistor
*2*2
Temperature in the machine displayed/Temperature in the machine displayed/
NG (Faulty)NG (Faulty)
DFDF
DDooccuummeennt t ddeetteeccttiioon n sseennssoorr NNo o ddooccuummeennt t / / DDooccuummeennt t sseett
DRDR
DoDocucumement nt scscanannnining g poposisitition on sesensnsoror No No dodocucummenent / t / DoDocucumement nt sesett
Note:Note:
•• When the sensoWhen the sensor is turned OFFr is turned OFF, “--” is displ, “--” is displayed on the LCD.ayed on the LCD.
•• When the functWhen the function is not mounion is not mounted or there is no itemted or there is no item, “**” is display, “**” is displayed on the LCD.ed on the LCD.