Turn the sheet over.
LS6374001
USA/CAN
Printed in China
Before you can use the machine, read this Quick Setup Guide
for the correct setup and installation.
Quick Setup Guide
DCP
-
165C
Important
DO NOT
connect the
USB cable yet.
a. The LCD shows:
No Cartridge
b.
Open the ink cartridge cover a.
3
Install the ink cartridges
4
d. Unpack the ink cartridge.
Turn the green knob on the protective yellow cap clockwise until it clicks to release the
vacuum seal, then remove the cap a.
If all lines are clear and visible, press o a
(Yes) to finish the quality check.
If you can see missing short lines, press o b
(No) and follow the steps on the LCD.
Connect the power cord
Set the LCD contrast (If needed)
7
5
Check the print quality
c. Remove the green protective
part a.
a. When the preparation process
has finished, the LCD shows
this message.
Set Paper and
Press Start
Press Color Start.
OK
Poor
Set the date and time
8
a. Press Menu.
b. Press a or b to choose 0.Initial Setup, and then
press OK.
c. Press a or b to choose 2.LCD Contrast, and then
press OK.
d. Press a or b to choose Dark or Light.
e. Press OK and then Stop/Exit.
a. Press Menu.
b. Press a or b to choose
0.Initial Setup, and then press OK.
c. Press a or b to choose
1.Date&Time, and then press OK.
6
Set the language (If needed)
b. Check the quality of the four color
blocks a on the sheet.
(black/yellow/cyan/magenta)
d. Press a or b repeatedly to enter the last two digits of the year, and
then press OK.
Year:2008
(e.g. Enter 08 for 2008.)
e. Repeat for Month and Day, and Hours and Minutes in 24-hour format.
f. Press Stop/Exit.
Note
If you make a mistake and want to start again,
press Stop/Exit to go back to step a.
a. Press Menu.
b. Press a or b to choose 0.Initial Setup, and then
press OK.
c. Press a or b to choose 0.Local Language, and then
press OK.
d. Press a or b to choose your language.
e. Press OK and then Stop/Exit.
WARNING
Warnings tell you what to do to
prevent possible personal injury.
Note
The components of your box may differ depending on your •
country.
Save all packing materials and the box in case for any •
reason you must ship your machine.
A USB cable is not included. •
You need to purchase a USB 2.0 cable that is no more
than 6 feet (2 meters) long.
Your machine has a USB 2.0 Full-speed interface. This interface
is compatible with USB 2.0 Hi-Speed; however, the maximum
data transfer rate will be 12 Mbits/s. The machine can also be
connected to a computer that has a USB 1.1 interface.
Important
DO NOT connect the
USB cable yet.
Note
The control panel
warning LED will stay on
until you have installed
the ink cartridges.
f. Gently push the ink cartridge until it clicks. After all the
ink cartridges are installed close the ink cartridge cover.
Note
The machine will prepare the ink tube system for printing.
This process will take approximately four minutes.
Do not turn off the machine.
Start Here
Unpack the machine and check the components
a. Remove the protective
tape and film.
b. Remove the plastic bag a
containing the ink cartridges
from on top of the paper tray.
c. Make sure you have all components.
1
Starter Ink
Cartridges [x4]
Black
Yellow
Cyan
Magenta
Accessory
Order Form
CD-ROM
Quick Setup
Guide
User’s Guide
Plastic bags are used in the packaging of your
machine. To avoid danger of suffocation, please
keep these bags away from babies and children.
WARNING
12
Load plain Letter/A4 paper
a. Pull out the paper tray. b. Lift the paper tray cover a. c. Press and slide the
paper side guides
a and paper length
guide b to fit the
paper size.
Make sure that the
triangular marks c
on the paper side
guides a and paper
length guide b line
up with the mark for
the paper size you
are using.
Important
Do not push the paper
in too far.
d. Fan the stack of paper well.
e. Gently put the paper into the paper tray. Check that the
paper is flat in the tray.
Note
When you use Legal size paper, press and hold the
universal guide release button
a as you slide out the
front of the paper tray.
1
f. Gently adjust the paper side guides to the paper with both hands.
Make sure the paper side guides touch the edges of the paper.
a. Connect the power cord.
e. Install each ink cartridge in the direction of the arrow on
the label. Take care to match the color of the lever a
with the cartridge color b.
g. Close the paper tray cover
and slowly push the paper
tray back into the machine.
h. Pull out the paper support a
until it clicks, and then unfold
the paper support flap b.
1
1
2
1
3
2
3
1
1
2
1
1
1
To Next Page
Need help?
General
