To Next PageTo Next Page
What to do if my Brother HL-2270DW cannot detect toner?
If your Brother printer can't detect the toner, it might be due to these reasons: * If the power was turned off or the front cover was opened while detecting a new toner cartridge, reset the developing bias voltage and develop roller counter. * If the new toner actuator is loose, re-assemble it. * If the new toner sensor has failed, replace the panel PCB assembly.
How to fix the pickup function of the paper tray on a Brother Printer?
If the pickup function of the paper tray on your Brother printer isn't working, consider these potential solutions: * If the link arm or pick-up roller holder assembly is catching, re-assemble them. * Check and reconnect the harness of the main motor if there's a connection failure. * If the plate-up gear (gear Z19M10 or lift gear 46) has failed, replace it. * The main motor, low voltage power supply PCB assembly, or main PCB assembly might need replacement.
What to do if my Brother HL-2270DW Printer does not feed paper from the manual feed slot?
If your Brother printer isn't feeding paper from the manual feed slot, try these solutions: * Check the harness connection of the registration front/rear sensor PCB ASSY and reconnect it if necessary. * The low voltage power supply PCB ASSY or the main PCB might be faulty and need replacement. * If the registration front/rear sensor is failing, check the sensor performance. If any problem occurs, replace the regist frame ASSY.
What to do if there is a paper jam at the paper tray and front cover section of my Brother HL-2270DW Printer?
If you're experiencing paper jams at the paper tray and front cover section of your Brother printer, consider the following: * Ensure that the paper edge actuator (on HL-2250DN/2270DW/2275DW models) or the registration front actuator isn't catching. Correct their positioning if needed. * Check and reconnect the harness connection of the registration front/rear sensor PCB ASSY if it's loose. * If the paper feeding roller is worn out, replace the paper feeding kit. * The low voltage power supply PCB ASSY or the main PCB might be faulty, requiring replacement. * Check the registration front and rear sensor performance. If any problem occurs, replace the regist frame ASSY.
What to do if my Brother Printer is not feeding paper?
If your Brother printer isn't feeding paper, there are several possible causes and solutions: * The lift arm and pick-up roller holder assembly may not be assembled correctly. In this case, re-assemble the lift arm and pick-up roller holder assembly. * Check the harness connections of the T1 clutch ASSY and the paper edge sensor harness ASSY, and reconnect them if necessary. * The paper feeding roller or the plate-up gear might be faulty, in this case replace the paper feeding kit or the plate-up gear. * The T1 clutch ASSY, panel PCB ASSY, or main PCB might have failed, requiring replacement. * For HL-2250DN/2270DW/2275DW models, check the paper edge sensor performance. If there are any issues, replace the PF frame ASSY.
What to do if Brother All in One Printer says no paper?
If your Brother All in One Printer displays a 'No Paper' error, it means the printer is out of paper or the paper isn't correctly loaded. Refill the paper in the paper tray and press Start, or remove the paper and load it again, then press Start. If the issue continues, the paper pick-up roller may need cleaning.
Why does my Brother HL-2270DW have paper jam inside and rear of the printer?
If your Brother printer is experiencing paper jams inside and at the rear, several factors could be responsible. The registration front actuator, registration rear actuator, or paper eject actuator might be catching. Ensure these actuators are correctly positioned. Check the harness connections of the registration front/rear sensor PCB ASSY or paper eject sensor PCB ASSY and reconnect if necessary. A faulty REG clutch ASSY, paper eject sensor PCB ASSY, low voltage power supply PCB ASSY, main PCB, or fuser unit could also be the cause, requiring replacement. Finally, the registration front/rear sensor PCB ASSY may be failing, requiring a check of the sensor performance. If a problem is detected, replace the regist frame ASSY.
What to do if my Brother HL-2270DW Printer has paper jam at paper tray and front cover section?
If you're experiencing paper jams in your Brother printer's paper tray and front cover area, it could be due to several reasons. The paper edge actuator or registration front actuator might be catching. Try correcting the position of the paper edge actuator or registration front actuator. Another cause might be worn out paper feeding kit, which requires replacement. Also, check the harness connection of the registration front/rear sensor PCB ASSY and reconnect it if necessary. In some cases, the low voltage power supply PCB ASSY or the main PCB might be faulty and require replacement. Finally, the registration front/rear sensor PCB ASSY may be failing, requiring a check of the registration front and rear sensor performance. If a problem is detected, replace the regist frame ASSY.
Why does my Brother Laser printer not feed paper?
If your Brother Laser printer does not feed paper, ensure that the paper in the paper tray is straight. If the paper is curled, straighten it before printing. Sometimes, removing the paper, turning the stack over, and then putting it back in the paper tray can help. If the paper continues to curl, replace the paper. Reduce the amount of paper in the paper tray, and then try again. Make sure that manual feed mode is not chosen in the printer driver. Clean the paper pick-up roller.
What to do if my Brother Laser printer is not printing?
If your Brother Laser printer is not printing, ensure the cable is securely connected to the machine. Verify that the machine is powered on and that no error LEDs are lit on the control panel. Also, confirm that you have selected the correct printer driver.
General| Color | No |
|---|---|
| N-up printing | 2, 4, 9, 16, 25 |
| Print technology | Laser |
| Maximum resolution | 2400 x 600 DPI |
| Economical printing | Yes |
| Time to first page (black, normal) | 8.5 s |
| Print speed (black, normal quality, A4/US Letter) | 27 ppm |
| Maximum internal memory | - MB |
| Sound power level (standby) | 31 dB |
| Sound pressure level (printing) | 53 dB |
| Total input capacity | 250 sheets |
| Total output capacity | 100 sheets |
| Total number of input trays | 1 |
| Maximum duty cycle | - pages per month |
| Custom media width | 76.2 - 216 mm |
| Maximum print size | 216 x 406 mm |
| Custom media length | 116 - 406.4 mm |
| Paper tray media types | Bond paper, Plain paper, Recycled paper |
| Paper tray media weight | 60 - 105 g/m² |
| Non-ISO print media sizes | Letter |
| ISO A-series sizes (A0...A9) | A4, A5, A6 |
| ISO B-series sizes (B0...B9) | B5, B6 |
| Multi-purpose tray media types | Bond paper, Envelopes, Heavyweight paper, Labels, Plain paper, Recycled paper, Transparencies |
| Maximum ISO A-series paper size | A4 |
| Multi-Purpose Tray media weight | 60 - 163 g/m² |
| Wi-Fi standards | 802.11b, 802.11g |
| Security algorithms | 128-bit WEP, 64-bit WEP, WPA-PSK, WPA-TKIP, WPA2-PSK |
| Sustainability certificates | ENERGY STAR |
| AC input voltage | 220 - 240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (standby) | 65 W |
| Power consumption (printing) | 495 W |
| Power consumption (PowerSave) | 0.9 W |
| Operating temperature (T-T) | 10 - 32.5 °C |
| Operating relative humidity (H-H) | 20 - 80 % |
| Package weight | 8300 g |
| Standard interfaces | Ethernet, USB 2.0, Wireless LAN |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| Mac operating systems supported | Mac OS X 10.4 Tiger, Mac OS X 10.5 Leopard, Mac OS X 10.6 Snow Leopard, Mac OS X 10.7 Lion |
| Server operating systems supported | Windows 2000 Advanced Server, Windows 2000 Server, Windows Server 2003, Windows Server 2003 x64, Windows Server 2008, Windows Server 2008 R2, Windows Server 2008 x64 |
| Windows operating systems supported | Windows 2000, Windows 2000 Professional, Windows 7 Home Premium, Windows 7 Home Premium x64, Windows 7 Professional, Windows 7 Professional x64, Windows 7 Starter, Windows 7 Starter x64, Windows 7 Ultimate, Windows 7 Ultimate x64, Windows Vista Business, Windows Vista Business x64, Windows Vista Home Basic, Windows Vista Home Basic x64, Windows Vista Home Premium, Windows Vista Home Premium x64, Windows Vista Ultimate, Windows Vista Ultimate x64, Windows XP Home, Windows XP Home x64, Windows XP Professional, Windows XP Professional x64 |
Weight and Dimensions| Dimensions (WxDxH) | 368 x 360 x 183 mm |
|---|
