To Next Page
T
Tina KleinAug 30, 2025
What to do if my Brother Laser printer says NO TONER?
- MMary PooleAug 30, 2025
If your Brother Laser printer displays 'NO TONER', open the front cover, then install the toner cartridge.
What to do if my Brother Laser printer says NO TONER?
If your Brother Laser printer displays 'NO TONER', open the front cover, then install the toner cartridge.
How to resolve 'Cartridge Error' on Brother Printer?
If you are getting a 'CARTRIDGE ERROR' on your Brother printer, make sure that the drum unit and toner cartridge assembly is installed properly.
What to do if my Brother All in One Printer displays 'Manual Feed'?
If your Brother All in One Printer displays 'Manual Feed', it means Manual Feed was selected as the paper source when there was no paper in the manual feed slot. Place a sheet of paper in the manual feed slot.
What does 'Replace Toner' mean on my Brother All in One Printer and how to fix it?
The 'Replace Toner' message on your Brother All in One Printer means the machine will stop printing until you replace the toner cartridge. If the Toner setting is set to Stop, replace the toner cartridge with a new, original Brother toner cartridge to reset the Replace Toner mode. If the Toner setting is set to Continue, the machine will continue printing until the LCD shows Toner Ended.
What does 'Size Error DX 1' mean on my Brother HL-2130 Printer?
If your Brother printer displays 'SIZE ERROR DX 1', choose a paper size supported by the duplex tray.
Why is my Brother Printer showing a paper size error?
If your Brother printer is displaying a paper size error, it could be due to: * The registration front actuator catching. Correct its position. * The main PCB might be faulty and need replacement.
How to delete the "Replace Toner" message on a Brother HL-2130 after replacing the toner?
If you're still seeing the "Replace Toner" message on your Brother printer after replacing the toner, consider the following: * The new toner actuator might be catching; correct its position. * Check and reconnect the harness of the Panel PCB if there's a connection failure. * The Panel PCB assembly or Main PCB assembly might need replacement.
How to fix 'Duplex Disabled 1' error on Brother Laser printer?
To fix the 'DUPLEX DISABLED 1' error on your Brother Laser printer, close the back cover of the printer and put the duplex tray back in.
What to do if my Brother HL-2130 Printer says 'Front Cover Open'?
If your Brother printer displays 'FRONT COVER OPEN', close the front cover of the machine.
What to do if my Brother HL-2130 has paper jam at paper tray and front cover section?
If you're experiencing paper jams in your Brother printer's paper tray and front cover area, it could be due to several reasons. The paper edge actuator or registration front actuator might be catching. Try correcting the position of the paper edge actuator or registration front actuator. Another cause might be worn out paper feeding kit, which requires replacement. Also, check the harness connection of the registration front/rear sensor PCB ASSY and reconnect it if necessary. In some cases, the low voltage power supply PCB ASSY or the main PCB might be faulty and require replacement. Finally, the registration front/rear sensor PCB ASSY may be failing, requiring a check of the registration front and rear sensor performance. If a problem is detected, replace the regist frame ASSY.
General| Network ready | No |
|---|---|
| N-up printing | 2, 4, 16, 25 |
| Print technology | Laser |
| Maximum resolution | 2400 x 600 DPI |
| Time to first page (black, normal) | 10 s |
| Print speed (black, normal quality, A4/US Letter) | 20 ppm |
| Maximum duty cycle | - pages per month |
| Number of print cartridges | 1 |
| Maximum internal memory | - MB |
| Sound power level (standby) | 31 dB |
| Sound pressure level (printing) | 53 dB |
| Display | LED |
| Total input capacity | 250 sheets |
| Total output capacity | 100 sheets |
| Custom media width | 69.9 - 215.9 mm |
| Maximum print size | 216 x 406 mm |
| Custom media length | 116 - 406.4 mm |
| Paper tray media types | Bond paper, Plain paper, Recycled paper |
| Paper tray media weight | 60 - 105 g/m² |
| Non-ISO print media sizes | Letter |
| ISO A-series sizes (A0...A9) | A4, A5, A6 |
| ISO B-series sizes (B0...B9) | B5, B6 |
| Multi-purpose tray media types | Bond paper, Envelopes, Heavyweight paper, Labels, Plain paper, Recycled paper, Transparencies |
| Maximum ISO A-series paper size | A4 |
| Multi-Purpose Tray media weight | 60 - 163 g/m² |
| Standard interfaces | USB 2.0 |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| AC input voltage | 220 - 240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (standby) | 62 W |
| Power consumption (printing) | 421 W |
| Power consumption (PowerSave) | 0.8 W |
| Package weight | 8000 g |
| Power LED | Yes |
| Sustainability certificates | ENERGY STAR |
| Mac operating systems supported | Mac OS X 10.4 Tiger, Mac OS X 10.5 Leopard, Mac OS X 10.6 Snow Leopard, Mac OS X 10.7 Lion |
| Windows operating systems supported | Windows 2000, Windows 2000 Professional, Windows 7 Home Premium, Windows 7 Home Premium x64, Windows 7 Professional, Windows 7 Professional x64, Windows 7 Starter, Windows 7 Starter x64, Windows 7 Ultimate, Windows 7 Ultimate x64, Windows Vista Business, Windows Vista Business x64, Windows Vista Home Basic, Windows Vista Home Basic x64, Windows Vista Home Premium, Windows Vista Home Premium x64, Windows Vista Ultimate, Windows Vista Ultimate x64, Windows XP Home, Windows XP Home x64, Windows XP Professional, Windows XP Professional x64 |
Weight and Dimensions| Dimensions (WxDxH) | 368 x 360 x 183 mm |
|---|
