How to delete the "Replace Toner" message on a Brother HL-2130 after replacing the toner?
If you're still seeing the "Replace Toner" message on your Brother printer after replacing the toner, consider the following: * The new toner actuator might be catching; correct its position. * Check and reconnect the harness of the Panel PCB if there's a connection failure. * The Panel PCB assembly or Main PCB assembly might need replacement.
What to do if my Brother HL-2130 cannot detect toner?
If your Brother printer can't detect the toner, it might be due to these reasons: * If the power was turned off or the front cover was opened while detecting a new toner cartridge, reset the developing bias voltage and develop roller counter. * If the new toner actuator is loose, re-assemble it. * If the new toner sensor has failed, replace the panel PCB assembly.
How to fix the pickup function of the paper tray on a Brother HL-2130?
If the pickup function of the paper tray on your Brother printer isn't working, consider these potential solutions: * If the link arm or pick-up roller holder assembly is catching, re-assemble them. * Check and reconnect the harness of the main motor if there's a connection failure. * If the plate-up gear (gear Z19M10 or lift gear 46) has failed, replace it. * The main motor, low voltage power supply PCB assembly, or main PCB assembly might need replacement.
What to do if my Brother HL-2130 Printer does not feed paper from the manual feed slot?
If your Brother printer isn't feeding paper from the manual feed slot, try these solutions: * Check the harness connection of the registration front/rear sensor PCB ASSY and reconnect it if necessary. * The low voltage power supply PCB ASSY or the main PCB might be faulty and need replacement. * If the registration front/rear sensor is failing, check the sensor performance. If any problem occurs, replace the regist frame ASSY.
What to do if there is a paper jam at the paper tray and front cover section of my Brother HL-2130?
If you're experiencing paper jams at the paper tray and front cover section of your Brother printer, consider the following: * Ensure that the paper edge actuator (on HL-2250DN/2270DW/2275DW models) or the registration front actuator isn't catching. Correct their positioning if needed. * Check and reconnect the harness connection of the registration front/rear sensor PCB ASSY if it's loose. * If the paper feeding roller is worn out, replace the paper feeding kit. * The low voltage power supply PCB ASSY or the main PCB might be faulty, requiring replacement. * Check the registration front and rear sensor performance. If any problem occurs, replace the regist frame ASSY.
What to do if my Brother Printer is not feeding paper?
If your Brother printer isn't feeding paper, there are several possible causes and solutions: * The lift arm and pick-up roller holder assembly may not be assembled correctly. In this case, re-assemble the lift arm and pick-up roller holder assembly. * Check the harness connections of the T1 clutch ASSY and the paper edge sensor harness ASSY, and reconnect them if necessary. * The paper feeding roller or the plate-up gear might be faulty, in this case replace the paper feeding kit or the plate-up gear. * The T1 clutch ASSY, panel PCB ASSY, or main PCB might have failed, requiring replacement. * For HL-2250DN/2270DW/2275DW models, check the paper edge sensor performance. If there are any issues, replace the PF frame ASSY.
What causes paper jam in the duplex tray of Brother Printer?
If your Brother printer is experiencing paper jams specifically in the duplex tray, first check for any foreign objects around the duplex tray and remove them. If jams persist, the duplex tray itself might be faulty and need replacement. Damaged DX gears could also be the cause, requiring replacement of the main frame L ASSY.
Why does my Brother Printer have paper jam inside and rear of the printer?
If your Brother printer is experiencing paper jams inside and at the rear, several factors could be responsible. The registration front actuator, registration rear actuator, or paper eject actuator might be catching. Ensure these actuators are correctly positioned. Check the harness connections of the registration front/rear sensor PCB ASSY or paper eject sensor PCB ASSY and reconnect if necessary. A faulty REG clutch ASSY, paper eject sensor PCB ASSY, low voltage power supply PCB ASSY, main PCB, or fuser unit could also be the cause, requiring replacement. Finally, the registration front/rear sensor PCB ASSY may be failing, requiring a check of the sensor performance. If a problem is detected, replace the regist frame ASSY.
What does toner low mean on Brother All in One Printer?
When your Brother All in One Printer shows 'Toner Low', it means you'll need to replace the toner cartridge soon. Purchase a new toner cartridge before you get a 'Replace Toner' message.
Why does my Brother Laser printer not feed paper?
If your Brother Laser printer does not feed paper, ensure that the paper in the paper tray is straight. If the paper is curled, straighten it before printing. Sometimes, removing the paper, turning the stack over, and then putting it back in the paper tray can help. If the paper continues to curl, replace the paper. Reduce the amount of paper in the paper tray, and then try again. Make sure that manual feed mode is not chosen in the printer driver. Clean the paper pick-up roller.
General| Network ready | No |
|---|---|
| N-up printing | 2, 4, 16, 25 |
| Print technology | Laser |
| Maximum resolution | 2400 x 600 DPI |
| Time to first page (black, normal) | 10 s |
| Print speed (black, normal quality, A4/US Letter) | 20 ppm |
| Maximum duty cycle | - pages per month |
| Number of print cartridges | 1 |
| Maximum internal memory | - MB |
| Sound power level (standby) | 31 dB |
| Sound pressure level (printing) | 53 dB |
| Display | LED |
| Total input capacity | 250 sheets |
| Total output capacity | 100 sheets |
| Custom media width | 69.9 - 215.9 mm |
| Maximum print size | 216 x 406 mm |
| Custom media length | 116 - 406.4 mm |
| Paper tray media types | Bond paper, Plain paper, Recycled paper |
| Paper tray media weight | 60 - 105 g/m² |
| Non-ISO print media sizes | Letter |
| ISO A-series sizes (A0...A9) | A4, A5, A6 |
| ISO B-series sizes (B0...B9) | B5, B6 |
| Multi-purpose tray media types | Bond paper, Envelopes, Heavyweight paper, Labels, Plain paper, Recycled paper, Transparencies |
| Maximum ISO A-series paper size | A4 |
| Multi-Purpose Tray media weight | 60 - 163 g/m² |
| Standard interfaces | USB 2.0 |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| AC input voltage | 220 - 240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (standby) | 62 W |
| Power consumption (printing) | 421 W |
| Power consumption (PowerSave) | 0.8 W |
| Package weight | 8000 g |
| Power LED | Yes |
| Sustainability certificates | ENERGY STAR |
| Mac operating systems supported | Mac OS X 10.4 Tiger, Mac OS X 10.5 Leopard, Mac OS X 10.6 Snow Leopard, Mac OS X 10.7 Lion |
| Windows operating systems supported | Windows 2000, Windows 2000 Professional, Windows 7 Home Premium, Windows 7 Home Premium x64, Windows 7 Professional, Windows 7 Professional x64, Windows 7 Starter, Windows 7 Starter x64, Windows 7 Ultimate, Windows 7 Ultimate x64, Windows Vista Business, Windows Vista Business x64, Windows Vista Home Basic, Windows Vista Home Basic x64, Windows Vista Home Premium, Windows Vista Home Premium x64, Windows Vista Ultimate, Windows Vista Ultimate x64, Windows XP Home, Windows XP Home x64, Windows XP Professional, Windows XP Professional x64 |
Weight and Dimensions| Dimensions (WxDxH) | 368 x 360 x 183 mm |
|---|
To Next Page
