What does '2 Line Limit! / 1 Line Limit!' mean on my Brother Label Maker?
The '2 Line Limit! / 1 Line Limit!' message on your Brother Label Maker indicates the following: * You tried to enter a 3rd line by pressing . * You tried to print or preview two lines of text while 0.13" (3.5mm) or 0.23" (6 mm) tape is installed. Install a larger tape size.
Why does my Brother P-touch Embellish not print or the printed characters are not formed properly?
If your Brother Label Maker is not printing correctly, check the following: * Ensure that the cassette is correctly inserted. * If the cassette is empty, replace it with a new one. * Make sure the Tape Cassette Cover is closed correctly.
Why does the Brother Label Maker power off when I try to print?
If your Brother Label Maker turns off when you try to print, it could be due to the following reasons: * The batteries may be weak, so try replacing them. * Ensure that the batteries are correctly inserted. * You might be using the wrong AC Adapter. It is recommended to use the AD-24ESA Adapter.
What to do if the tape does not feed properly or gets stuck inside my Brother P-touch Embellish?
If the tape in your Brother Label Maker isn't feeding correctly or gets stuck, check that the end of the tape feeds under the tape guides. Also, make sure you are not touching the Cutter Lever during printing.
How to clear all text and format settings on my Brother P-touch Embellish?
To clear all text and format settings on your Brother Label Maker to create a new ribbon/tape: * Press + and select [Text&Format]. * Alternatively, press / [Clear] / [Text&Format].
Why does the setting clear on my Brother P-touch Embellish Label Maker by itself?
If the settings on your Brother Label Maker are clearing on their own, it could be due to weak batteries. Try replacing them. Also, if the power is disconnected for more than three minutes, all text and formats in the display settings will be cleared.
What does 'No Frame OK?' mean on my Brother Label Maker?
The 'No Frame OK?' message on your Brother Label Maker appears because: * You have used a frame or Frame settings are ON, but a cassette narrower than 0.47"(12mm) is installed (Frames for use ONLY with 0.47"(12mm) cassettes). * Select to print with no Frame, press to cancel.
What does 'Cutter Pressed' mean on my Brother P-touch Embellish?
The 'Cutter Pressed' message on your Brother Label Maker means that the Tape Cutter Lever was pressed in the middle of the printing process.
What does 'No Text!' mean on my Brother Label Maker?
The 'No Text!' message on your Brother Label Maker appears in the following situations: * If you try to print a text file when there is no data stored in the memory. * If is pressed when no text is entered. * If + is pressed when no text is entered. * If is pressed when no text is entered. * If or was pressed when no text is entered while using templates.
Why does my Brother P-touch Embellish Label Maker say 'Text Full!'?
The 'Text Full!' message on your Brother Label Maker indicates that you have reached the maximum number of characters allowed. This is 80 characters for regular text and 50 characters for templates.
General| Type | Label Maker |
|---|---|
| Technology | Thermal Transfer |
| Print Resolution | 180 dpi |
| Print Speed | up to 20 mm/sec |
| Display | LCD |
| Keyboard | QWERTY |
| Connectivity | USB |
| Label Widths Supported | 12 mm |
| Max. Label Length | 1 m |
| Tape Type | TZe tape |
| Power Source | AC adapter or batteries |
| Model | Brother P-touch Embellish |
| Cutter | Auto and Manual |
Instructions on how to install power supply and tape or ribbon cassette.
Guidelines to avoid fire, burns, injury, electric shocks, and other hazards.
Advice to avoid personal injury, liquid leakage, burns, or heat.
Steps to turn on the machine and set initial language and measurement units.
Covers text input, switching case, and using the enter key for new lines.
How to preview print output and feed blank tape.
Steps for printing labels, including copy count and tape cutting.
Procedure to reset the printer to factory settings, clearing all data and configurations.
To Next Page