47
Spa Model Dimensions
Model Width Length Height
M9
7' 10" (2.39m) 9' 2" (2.80m) 38"
(.97m)
M8
7' 10" (2.39m 7' 10" (2.39m 38"
(.97m)
M7
7' 7" (2.31m) 7' 7" (2.31m) 37"
(.94m)
M6
6' 8" (2.03m) 7' 7" (2.31m) 34"
(.86m)
A9L
7' 10" (2.39m) 9' 2" (2.80m) 38"
(.97m)
A8, A8L, A8D,
R8, R8L, X8
7' 10" (2.39m 7' 10" (2.39m 38"
(.97m)
A7, A7L, R7,
R7L, X7, X7
7' 4" (2.24m) 7' 4" (2.24m) 36"
(.91m)
A6, A6L, R6,
R6L, X6L
7' 4" (2.24m) 6' 8" (2.03m) 34"
(.86m)
A5L, R5L,
X5L
5' 8" (1.73m) 7' 0" (2.13m) 31"
(.79m)
X6R
6' 7" (2.01m) 6' 7" (2.01m) 36"
(.91m)
STIL7
7' 4" (2.24m) 7' 0" (2.13m) 34"
(.86m)
STIL5
7' 0" (2.13m) 5' 8" (1.73m) 31"
(.79m)
Corner Radius for A, & R, & X Models is 8” (0.3937m)
Corner Radius for M Series & STIL Models is 2.5” (0.0635m)
Electrical Requirements
Installation Instructions
IMPORTANT: Provide a copy of these instructions to your
Electrician. e installation of all spas must be in accordance
with national and local wiring rules. Always have a licensed
Electrician perform the electrical installation. Each Bullfrog Spa
is manufactured and tested to a standard that provides maximum
protection against electrical shock. Improper wiring may prevent
the spa from operating safely which could result in electrical
shock, injury or death. Improper wiring could also lead to a
malfunction of the spa’s equipment and risk of re.
Drilling Conduit Hole:
All dimensions are at the bottom base.
1” (2.54cm) Conduit Drill 1-3/8” (3.49cm) hole 3/4” (1.91cm)
Conduit Drill 1-1/8” (2.86cm) hole Center of hole is 1” (2.54cm)
from the ground
Important Technical Information
Voltage Denitions: When reading these instructions, the term
120V~ refers to the 110-120V~ range of voltage, while the 240V~
term refers to the 220-240 range of voltage.
Wiring Connection: Appliance must be permanently
connected to xed wiring (except for U.S./CAN 120V~/60Hz
Cord-Connected units).
Wiring Diagrams: In addition to the instructions that follow,
please reference the appropriate Wiring Diagrams (120V~/60Hz
Cord-Connected, 120V~/60Hz Permanently-Connected,
240V~/60Hz Permanently-Connected, or 230V~/50Hz
Permanently-Connected).
Electrical Service Wire Size and Type: e size of wire
required to supply the spa with power is dependent upon the
length of the electrical run and should only be determined by a
licensed Electrician. Installation must be in accordance with all
national and local wiring rules. All wiring from the disconnect to
the spa must be copper to ensure adequate connections. Never
use aluminum wiring from the GFCI disconnect to the spa”
Spa Location:
Overhead Power Lines: Based upon the national and local wiring
rules that apply to your area, you will need to install your spa at
the required minimum horizontal and vertical distances from all
power lines.
Service Disconnect: Based upon your area, a disconnect
device must be incorporated into the xed wiring in accordance
with national and local wiring rules. If the national and local
wiring rules permit, a GFCI Sub Panel may be used to substitute
the service disconnect, providing that it is located within the same
parameters.
Electrical Outlets, Switches and Devices: Based upon
the national and local wiring rules that apply to your area, you
must install your spa at or beyond the required minimum distance
from all electrical outlets, switches, and devices.
Bonding: Based upon the national and local wiring rules that
apply to your area, the Control System Box located inside the
equipment compartment of your spa must be bonded to all metal
equipment, handrails, xtures, enclosures, pipe, or conduit that
are located within the maximum specied distances. e bonding
is to be connected to the ground lug connector on the exterior
surface of the Control System Box and all metal items previously
described.
Equipment Compartment Access: Make sure the spa is
positioned so that access to the equipment compartment will not
be blocked.
To Next Page
Loading...
