What does 'ERROR3' mean on my Burkert Controller and how do I fix it?
If the device state LED on your Burkert Controller is red with the message 'ERROR3', it signifies that the user parameters have been lost. Try restarting the device. If the message persists, reconfigure the device.
What does 'CONTINUE' mean on my Burkert Controller?
If the device state LED on your Burkert Controller is any colour and displays the message 'CONTINUE', it indicates that the power supply was interrupted during a dosing, causing the dosing to be interrupted. Check the electrical installation. You can either abort the current dosing or continue it, but in the latter case, verify that the current dosing is accurate.
What does 'W. BATCH' mean on my Burkert Controller?
If the device state LED on your Burkert Controller is orange and displays the message 'W. BATCH', it means the number of completed dosings has reached the value specified in the 'BATCH-W.' parameter of the Test menu. To address this, perform the planned maintenance operation and reset the daily totalizer of the completed dosings.
What does 'WARN. VOL.' mean on my Burkert Controller?
If the device state LED on your Burkert Controller is orange and displays the message 'WARN. VOL.', it indicates that the daily volume or mass totalizer has reached the value set in the 'VOLUME-W.' parameter of the Test menu. Perform the planned maintenance operation and reset the daily volume or mass totalizer.
What to do if my Bürkert Transmitter shows 'PWR FAIL'?
If the Bürkert Transmitter displays 'PWR FAIL', it indicates that the supply voltage is too low. This could be because the voltage at the device terminals is below 12 V or the impedance of the current measurement loop is too high. To resolve this, adjust the supply voltage to ensure the voltage at the device terminals is between 12 V and 36 V.
What does 'WARN. HIG' mean on my Burkert Controller?
If the device state LED on your Burkert Controller is orange and displays the message 'WARN. HIG', it means that the measured flow rate has remained above the maximum threshold for the set time delay during a dosing. You should check the flow rate in the pipe and its effect on the process. Clean the flow sensor, if necessary. After the dosing is finished, access the Information menu and confirm the message.
Why is my Burkert Controller showing 'WARN. LOW'?
If the device state LED on your Burkert Controller is orange and displays the message 'WARN. LOW', it signifies that the measured flow rate has remained below the minimum threshold for the set time delay during dosing. Check the flow rate in the pipe and its impact on the process. If needed, clean the flow sensor. After the dosing is complete, go to the Information menu and confirm the message.
What to do if Burkert Controller device state LED is red with message 'dosing being done...'
If the device state LED on your Burkert Controller shows red with the message 'dosing being done...', it indicates that the rotational frequency of the paddle wheel exceeds 2.2 kHz. To fix this, check the flow rate in the pipe and adjust it as necessary. If the issue persists, further assistance might be required.
Why is the device state LED on my Burkert Controller red with message 'PWRFAIL'?
If the device state LED on your Burkert Controller displays red with the message 'PWRFAIL', it means the supply voltage is too low, preventing the device from functioning correctly. To resolve this, verify that the supply voltage is within the range of 12 to 36 V DC. If the problem continues after confirming the voltage, further assistance may be needed.
How to troubleshoot a Burkert Controller when the device state LED is OFF?
If the device state LED on your Burkert Controller is off, it indicates that the device is not receiving power. You should first check the wiring to ensure it is correctly connected. Also, inspect the installation's fuse and replace it if needed. Verify that the installation hasn't been shut down and confirm that the power source is functioning correctly. If the issue persists after these checks, it may indicate a more complex problem.
General| Category | Transmitter |
|---|---|
| Power Supply | 12-36 V DC |
| Measuring Principle | Electromagnetic |
| Pipe Diameter | DN 06 to DN 400 |
| Protection Class | IP65 |
| Display | Yes |
| Output Signal | 4-20 mA, Pulse, Frequency, Relay |
| Temperature Range | -10 to 60 °C |
| Process Connection | Threaded, flanged, or clamped |
| Wetted Materials | Stainless steel, FKM |
| Medium Temperature | -10 to 100 °C |
| Housing Material | Stainless steel, Plastic |
| Relative Humidity | 5-95% non-condensing |
| Accuracy | ±0.5% of reading |
To Next Page
