To Next PageTo Next Page
Need help?Do you have a question about the Canon WP-DC26 and is the answer not in the manual?
General| Brand | Canon |
|---|---|
| Model | WP-DC26 |
| Category | Digital Camera |
| Language | English |
Canon disclaims liability for errors or omissions in the guide's information.
Reproduction or translation requires prior written permission from Canon.
Canon is not liable for damages from data loss due to mistaken operation or malfunctions.
Read manual carefully for correct operation and store it safely for future reference.
Use camera in rain, beach, underwater up to 40m, and in wet/dusty environments.
Perform leak test by submerging empty case at 15cm depth for three minutes before initial use.
Check package contents against the list: WP-DC26 Case, straps, diffusion plate, grease, user guide.
Contact your Canon dealer if any items are missing from the package upon receipt.
Avoid high temperatures, direct sunlight, and adhere to operating temperature limits for case integrity.
Maintain seal cleanliness, avoid modification, and handle with care to prevent leaks.
Do not use as flotation device, mind depth limits, and avoid excessive force on controls.
Use wrist strap underwater; remove neck strap to prevent entanglement hazards.
Avoid dropping/throwing; use only supplied grease; avoid water near opening/closing.
Limit hot temp use; keep warm in cold; manage condensation from rapid temperature changes.
Stop shooting immediately if a leak occurs; never use the case in this state.
Dry interior thoroughly and contact Canon Support if leaks are detected.
Keep seal free of debris; clean gently without damage; avoid contamination.
Mount seal level without force; apply grease sparingly; do not use paper/cloth for application.
Damaged seals cause leaks; contact support. Replace seal annually for best performance.
Wash exterior with fresh water (under 30°C) after use; dry with soft cloth.
Soak in fresh water after salt water use to remove salt deposits.
Wipe interior with a soft, dry cloth; do not wash with water.
Identifies front components: Strap Mounts, Shutter, Zoom, Power, Lens Window, Grip, Diffusion Plate, Cord Mount, Tripod Socket.
Identifies back components: Mode Switch, Playback, ISO/Jump, Flash, FUNC./SET, DISP., MENU, Lock Release, Catch.
Keep lens window clean with a soft, dry cloth for clear photographs.
Insert charged battery (NB-5L) and memory card, confirming methods in the Camera User Guide.
Ensure sufficient storage space on the memory card for image recording.
Manage camera straps: remove original, attach neck/wrist straps to case mounts.
Slide the lock release switch and release the catch to open the back cover of the case.
Apply anticondensation solution only to the lens window's inside surface with a soft cloth.
Insert the camera into the Waterproof Case as shown in the diagram.
Close the case, ensuring the seal and contact surfaces are free of debris for leak prevention.
Make sure the case catch is fastened properly to secure the closure.
Turn on camera, set mode switch, and adjust settings using zoom lever.
Understand control dial operation and use Underwater Scene mode for optimal results.
Manually set white balance by assigning function to a button for custom adjustments.
Compose shots, press shutter halfway, wait for indicator, then press fully.
Ensure lens window is clean and fingers don't obstruct critical elements.
Attach diffusion plate for even flash; avoid scratching its surface.
Pass cord through mount, thread diffusion plate onto cord, and insert tip into indentation to attach.
Grip the diffusion plate and detach it by lifting off in the direction shown by the arrow.
Press the (Playback) button to enter playback mode and view images.
When finished using the camera, turn the camera off.
Dry case thoroughly, remove debris, and wash with tap water for salt deposits.
Slide lock release switch and catch to open case and remove camera, preventing interior contamination.
Wipe the interior with a soft, dry cloth; do not wash with water.
Store the case in an opened state to prevent seal deforming and maintain waterproof effect.
Protect the waterproof seal from dust or scratches during storage.
Do not store in hot, cold, humid places, or near naphthalene or insecticides.
Max depth 40m (JIS class 8), temperature 0-40°C, and materials like Polycarbonate, ABS.
Dimensions: 132.4x87.1x69.9mm. Volume: 465cm³. Weight: 295g.
Specifications subject to change; data based on Canon's testing standards.
