3
57
English
56
English
To establish a (wireless) connection between the Amp 5�1 and (Smart) speakers, please do the following:
1
Caution: Before starting the pairing process, the speaker to be paired (slave speaker) must have been disconnected from the mains for at least
30 seconds� Please unplug the power chord from the mains or switch the speaker off using the power switch�
2
To enter the menu, press the "M" button�
3
Use the " " or " " button to select the menu item Output Setup [OPS] and confirm with the "OK" button�
4
Use the " " or " " button to select the menu item Speaker Mapping [SPM] and confirm with the "OK" button�
5
Use the " " or " " button to select the speaker that you want to adjust and/or pair and confirm with the "OK" button�
If you did not set a speaker or pair of speakers to Smart in the Speaker Config menu [SPC], this option will not be available and Wireless can not
be selected�
6
Use the "+" resp� the "–" key to chose between Wireless (if available) and Analog (Analog 1 – Analog 5 / Analog6)�
If you want to use the outputs Analog 1 – Analog 5 and/or Analog 6 / Sub Out you can exit the menu after selecting the output by pressing the
"M" button�Please repeat this step for all "not Smart" speakers�
7
If you want to connect your Smart speaker, "Wireless" will be the only selectable option� The abbreviations behind Wireless have the following
meanings:
• Wireless (DIS) = Smart speaker not connected (Disconnected)
• Wireless (PIR) = Smart speaker pairing started (Pairing)
• Wireless (CON) = Smart speaker connected
8
Pressing the "OK" button guides you to the pairing process� The indication on the screen changes from Wireless to Wireless(PIR)�
The info bar on top of the menu changes from "Wireless pairing press OK" to "Pairing in process"� The display shows the selected speaker�
9
Connect the speaker you want to pair to the mains and – if applicable – switch this speaker on at the power switch within 20 seconds�
It does not matter if the speaker remains in stand by mode or if it starts up after you connected it to the mains�
10
After a few seconds a successful wireless pairing will be indicated with Wireless(CON) behind the selected speaker on the screen�
The newly paired Smart speakers shows [CON] in its display� From now on the displays of the Smart Amp 5�1 and the paired Smart speaker are in
sync and show the selected speaker� The infor bar on top of the menu shows "Pairing successful"�
11
The Amp 5�1 automatically jumps to the next speaker in the list after a successful pairing� Please repeat the steps 7 to 10 to connect additional
speakers�
12
Exit the menu item by pressing the "M" button�
Notes: If the speaker pairing failed and "Wireless pairing failed" is shown in the info bar on top of the menu please repeat steps 7 to 10
and verify that…
a) ���the selected Smart speaker has been disconnected from the mains for at least 30 seconds�
b) ���not more then 20 seconds have been passed between pressing the "OK" button and switching the speaker on�
c) ���the distance between the Amp 5�1 and the speaker may not exceed 10m and they are in the same room�
Please increase the transmission power of the wireless audio module described in chapter Transmission Power [TXP] if neccessary�
6. System Info [INF]
The fifth menu item of the Main Menu is the System Info� It contains the following items:
• Firmware Info [FWI]
– WiFi [WIF]
– Google Cast [GC]
– STS Wireless [STS]
– MCU Host [MCU]
– DSP Audio [DSP]
– OSD Fonts [OSD]
• Network Info [NWI]
– IP Address [IP]
– MAC Address [MAC]
– Name [NAM]
– SSID [SSI]
– WiFi Band [BAN]
– STS Wireless [WCH]
To Next Page
Loading...
