Canton Smart Vento 9 - User Manual

Questions and Answers

M
Miguel YatesSep 12, 2025
Why don't all speakers play a signal when Line or Balanced input is selected on my Canton Smart Vento 9?
- R
  Renee JohnsonSep 12, 2025
  If one or more speakers do not play a signal when the Line or Balanced input is selected on your Canton Stereo System, and the parameter ASM is set to DST, ensure you connect the left channel of the source unit to the jack marked L of the left speaker and the right channel of the source unit to the jack marked R of the right speaker. If balanced (Analogue Balanced) input is selected, the source must be connected directly to all speakers, paying attention to the correct channel assignment.
A
Andrew WebsterSep 10, 2025
Why do two speakers play the same channel on my Canton Stereo System?
- A
  Audrey NorrisSep 10, 2025
  If two speakers play the same channel on your Canton Stereo System, the master may have been assigned the same channel as a slave speaker during pairing. First use the test tone to check which speaker is playing the wrong channel. If it is the master, simply change the channel assignment of the master. If it is a slave, reconnect this speaker and select the correct channel. Alternatively, two slave speakers may have been assigned the same channel during pairing. First use the test tone to check which speaker is playing the wrong channel. Reconnect this speaker and select the correct channel.
M
Michael ValdezSep 9, 2025
What should I do if coupling of the slave speaker fails on my Canton Stereo System?
- M
  melissa57Sep 9, 2025
  If coupling of the slave speaker fails on your Canton Stereo System, disconnect the slave speaker to be paired for at least 30 seconds from the mains. After turning on the power switch of the slave speaker, turn it on by pressing the power button on the remote control. Always start pairing at the master before connecting the slave to the mains. Reduce the distance between master and slave. The maximum distance is 10 m in the same room.
J
Jasmine Lee DDSAug 23, 2025
Why is my Canton Stereo System speaker system not responding to the remote control?
- M
  Martin JenningsAug 23, 2025
  If your Canton Stereo System speaker system isn't responding to the remote, the battery might be dead. Replace the battery, ensuring correct polarity during insertion. Alternatively, check for and remove any protective film on the remote control.
M
Michael Dawson Jr.Sep 6, 2025
Why does Bluetooth playback start automatically when I turn on my Canton Smart Vento 9 Stereo System?
- S
  Shannon BergerSep 7, 2025
  If playback of the Bluetooth® device starts automatically when your Canton Stereo System is switched on, the automatic Bluetooth® playback (APL) function is activated (ON). Set the APL function to OFF, according to the chapter “automatic Bluetooth® playback.”
C
christine93Sep 5, 2025
Why is there no playback via Bluetooth® on my Canton Stereo System?
- R
  Richard WilliamsSep 5, 2025
  If there is no playback via Bluetooth® wireless technology on your Canton Stereo System, ensure there is a connection between the speaker system and the mobile end device. If the mobile end device is paired but not playing, reconnect it. Also, set the volume on the mobile end device to the maximum possible value and increase the volume of the speaker system. Ensure that sources of interference, such as a WiFi router or a laptop, are not placed in close proximity to the speaker system. If you are using both WiFi and Bluetooth® on a mobile end device, disable WiFi. Finally, reduce the distance between the speaker and the mobile end device, as you may be out of range (max. 10 m).
J
jenniferfoxSep 4, 2025
Why doesn't my Canton Stereo System automatically switch to the BT input?
- B
  Brian HenrySep 4, 2025
  If the speaker system does not automatically switch to the BT input, it may be because the BTS function is deactivated (MAN). Activate the BTS function (AUT). Also, ensure that Bluetooth® is enabled on your end device. If the speaker system is connected to another end device, disable Bluetooth® on the other device. Finally, ensure that the end device is paired with the speaker system.
R
Robert BrownSep 3, 2025
Why can't I select the BT input via the Input buttons on my Canton Smart Vento 9?
- G
  garrettzunigaSep 3, 2025
  If the BT input cannot be selected via the “Input” buttons on your Canton Stereo System, the function BTS is likely activated. In this case, switching happens automatically when the speaker system detects an audio signal from the end device.
C
Christina JacksonSep 2, 2025
Why does my Canton Smart Vento 9 speaker system unintentionally switch on?
- A
  Amber ThompsonSep 2, 2025
  If your Canton Stereo System is unintentionally switching on, it could be triggered by system sounds from your mobile device (like keyboard typing), a digital source turning on, or an analog source playing. Change the standby function (ECO, MAN or NSB).
M
Michael BarnettSep 1, 2025
Why does my Canton Smart Vento 9 speaker system not turn off automatically?
- J
  James HernandezSep 1, 2025
  If your Canton Stereo System speaker system does not turn off automatically, the standby function MAN might be activated. Activate the standby function ECO, AUT or NSB. If the standby function AUT or NSB is activated and the source device transmits a carrier signal in standby mode (optical or coaxial digital input), disconnect the source device from the mains or manually switch off the speaker system.