12 Instruction manual C873G, C866G & C848G Please keep this instruction manual for future reference
USING YOUR GAS HOB
USING YOUR GAS HOB
All operations concerning installation, adjustment and adaptation to
the available gas type must be carried out by a qualified technician,
in compliance with statutory legislation.
The symbols printed above each burner control show the correspondence between the
control and the burner.
S T A N DBY MODE
After connecting the appliance to the power supply, it will perform a brief self-diagnosis
routine and touch panel calibration (all displays and LEDs remain illuminated for a few
seconds). When this procedure is completed the display will be blank.
S W ITCHING ON THE HOB
To switch on the hob, hold the ON/OFF button for at
least 2 seconds.
The appliance will switch on and the five burner
displays will show power level 0, meaning that
the burners are off.
ALL OPERATIONS CONCERNING INSTALLATION, ADJUSTMENT AND
ADAPTATION TO THE AVAILABLE GAS TYPE MUST BE CARRIED OUT
BY A QUALIFIED TECHNICIAN, IN COMPLIANCE WITH STATUTORY
LEGISLATION.
The symbols printed above each burner control show the correspondence between the control and
the burner.
START-UP WITHOUT VALVES
Turn the corresponding knob anticlockwise to the maximum
position and press the knob.
AUTOMATIC START-UP WITH VALVES
› Turn the corresponding knob anticlockwise to the maximum
position (Fig.1) and press the knob.
› Once the burner has been started up, keep the knob pressed for about 6 seconds.
USING THE BURNERS
› To obtain the maximum efficiency without wasting
gas, the pot diameter must be suitable in relation to
the burner (see the following table), to avoid the flame
extending beyond the bottom of the pan.
› Use the maximum capacity to quickly make liquids reach
the boiling temperature, and the reduced capacity to heat food or maintain the boil. All of
the operating positions must be chosen between the maximum and the minimum ones, never
between the minimum position and the closing point.
› The gas supply can be interrupted by turning the knob clockwise up to the closing position. If
there is no power supply, it is possible to light the burners with matches, setting the knob to
the start-up point (maximum flame).
USING THE BURNERS
› To obtain the maximum efficiency without
wasting gas, the pot diameter must be
suitable in relation to the burner (see the
following table), to avoid the flame extending
beyond the bottom of the pan.
› Use the maximum capacity to quickly make liquids reach the boiling temperature, and the
reduced capacity to heat food or maintain the boil. All of the operating positions must be
chosen between the maximum and the minimum ones, never between the minimum
position and the closing point.
› The gas supply can be interrupted by turning the knob clockwise up to the closing position.
If there is no power supply, it is possible to light the burners with matches, setting the knob to
the start-up point (maximum flame).
Closed
Maximum
Minimum
S T A R T -UP WITHOUT VALVES
Turn the corresponding knob anticlockwise to the
maximum position and press the knob.
AUTOMATIC START-UP WITH VALVE S
› Turn the corresponding knob anticlockwise to the
maximum position (Fig.1) and press
the knob.
› Once the burner has been started up, keep the knob
pressed for about 6 seconds.
Fig.1
USING YOUR GAS HOB
All operations concerning installation, adjustment and adaptation to
the available gas type must be carried out by a qualified technician,
in compliance with statutory legislation.
The symbols printed on the side each knob show the correspondence between the knob and
the burner.
USING THE BURNERS
› To obtain the maximum efficiency without
wasting gas, the pot diameter must be
suitable in relation to the burner (see the
following table), to avoid the flame extending
beyond the bottom of the pan.
› Use the maximum capacity to quickly make liquids reach the boiling temperature, and the
reduced capacity to heat food or maintain the boil. All of the operating positions must be
chosen between the maximum and the minimum ones, never between the minimum
position and the closing point.
› The gas supply can be interrupted by turning the knob clockwise up to the closing position.
If there is no power supply, it is possible to light the burners with matches, setting the knob to
the start-up point (maximum flame).
Closed
Maximum
Minimum
S T A R T -UP WITHOUT VALVES
Turn the corresponding knob anticlockwise to the
maximum position and press the knob.
AUTOMATIC START-UP WITH VALVE S
› Turn the corresponding knob anticlockwise to the
maximum position (Fig.1) and press
the knob.
› Once the burner has been started up, keep the knob
pressed for about 6 seconds.
Fig.1
USING YOUR GAS HOB
All operations concerning installation, adjustment and adaptation to
the available gas type must be carried out by a qualified technician,
in compliance with statutory legislation.
The symbols printed on the side each knob show the correspondence between the knob and
the burner.
To Next Page
Loading...
