Carrier 33CS420-01 - Section 5 Viewing Temperature and Humidity; Viewing Outside Temperature; Viewing Indoor Humidity

89 pages

To Next Page

To Previous Page

Section 5 Contents:

Viewing the Outside

Temperature..............................5.2

Viewing the Indoor

Humidity....................................5.3

Page 5.1

SECTION 5

Viewing the Temperature and Humidity SensorsViewing the Temperature and Humidity Sensors

Carrier

Main Page

How to Use this Manual3
Glossary of Terms4
Table of Contents6
Quick Start7
- Setting the Clock8
- Setting the Day8
- Selecting the Heat or Cool Mode9
- Selecting Your Desired Temperature (Adjusting the Setpoints)10
- Using the Fan Button10
Section 1 Contents11
Getting to Know Your Thermostat11
- Front Panel12
- Display Features13
Setting the Clock and Day16
- Mode17
Basic Operation18
Selecting Your Desired18
- Programmable or Non-Programmable Thermostat19
- Manual or Auto-Changeover Thermostat20
- Operating Mode When the Thermostat Is Configured to be21
- Heat or Cool Mode25
- Auto or Program Mode25
- Selecting Your Desired Temperature (Adjusting Setpoints)25
- Viewing the Temperature and Humidity Sensors26
- Viewing the Outside Temperature27
- Viewing the Indoor Humidity28
Programming the Daily Schedule29
- Programming a Daily Schedule30
- Programming Tips33
- Overriding the Daily Schedule34
Programming the Fan Operation35
- Smart Fan Operation36
- Setting the Fan-Off Time Delay37
Thermostat Display Options38
- Turning On/Off the Backlight39
- Programming the Thermostat to Display Temperature in Fahrenheit or Celsius39
- Locking/Unlocking the Keypad40
- Front Panel Buttons40
- Programming a Security Level41
Humidification42
- Installing the Humidity Module43
- Setting a Thermostat Jumper for Humidity Operation44
- Adjusting the Humidification Setpoint45
Dehumidification46
- Setting a Thermostat Jumper for Dehumidification Operation47
- Adjusting the Dehumidification Setpoint48
- Using Your Air Conditioner to Dehumidify49
- Using the Dehum Terminal50
Viewing Equipment Run-Times51
- Viewing the Override Operation Run-Time52
- Viewing the Humidification Run-Time53
- Viewing the UV Light Run-Time54
Electric Heat and Heat Pump Operation55
- Viewing the Heat Pump and Reversing Valve Jumper Settings56
- Viewing the Electric Heat Jumper Setting57
- Using Emergency Heat58
Timers and Deadbands59
- Adjusting the Heat/Cool Differential60
- Adjusting the Cycles Per Hour61
- Adjusting the Deadband62
- Adjusting the Minutes of Run-Time64
- Before the Next Stage64
- Selecting 2Nd Stage Turn65
- Off Temperature65
- How to Use the Energy Save Feature66
Energy Save Operation66
- Programming Run-Time Alerts67
- How to Set and Reset the Service Filter (Fan Run-Time) Alert68
- How to Set and Reset the UV Light Run-Time Alert69
- How to Set and Reset the Humidifier70
- Run-Time Alert70
Programming the Holiday Mode71
Overriding the Holiday Mode72
Configuring the MISC Outputs73
- Configuring the Jumpers74
- Hum Jumper Setting75
- W3 Jumper Setting75
- Explanation of Jumper Settings75
- Dehum Jumper Setting76
- Y2 Jumper Setting77
Factory Defaults, Calibration, and Sensors78
- Resetting the Thermostat to the Factory Default Settings79
- Calibrating the Temperature and Humidity Sensors80
Accessories81
- Advanced Setup Table82
- Index83

Carrier 33CS420-01 - Section 5 Viewing Temperature and Humidity; Viewing Outside Temperature; Viewing Indoor Humidity

Table of Contents

Other manuals for Carrier 33CS420-01

Related product manuals