Carrier 33CS420-01 - Section 18 Factory Defaults, Calibration, and Sensors; Resetting to Factory Default Settings; Calibrating Temperature and Humidity Sensors

89 pages

To Next Page

To Previous Page

Page 18.1

Section 18 Contents:

Resetting the Thermostat to the

Factory Default Settings........18.2

Calibrating the Temperature

and Humidity Sensors...........18.3

SECTION 18

Factory Defaults, Calibration, and SensorsFactory Defaults, Calibration, and Sensors

Carrier

Main Page

How to Use this Manual3
Glossary of Terms4
Table of Contents6
Quick Start7
- Setting the Clock8
- Setting the Day8
- Selecting the Heat or Cool Mode9
- Selecting Your Desired Temperature (Adjusting the Setpoints)10
- Using the Fan Button10
Section 1 Contents11
Getting to Know Your Thermostat11
- Front Panel12
- Display Features13
Setting the Clock and Day16
- Mode17
Basic Operation18
Selecting Your Desired18
- Programmable or Non-Programmable Thermostat19
- Manual or Auto-Changeover Thermostat20
- Operating Mode When the Thermostat Is Configured to be21
- Heat or Cool Mode25
- Auto or Program Mode25
- Selecting Your Desired Temperature (Adjusting Setpoints)25
- Viewing the Temperature and Humidity Sensors26
- Viewing the Outside Temperature27
- Viewing the Indoor Humidity28
Programming the Daily Schedule29
- Programming a Daily Schedule30
- Programming Tips33
- Overriding the Daily Schedule34
Programming the Fan Operation35
- Smart Fan Operation36
- Setting the Fan-Off Time Delay37
Thermostat Display Options38
- Turning On/Off the Backlight39
- Programming the Thermostat to Display Temperature in Fahrenheit or Celsius39
- Locking/Unlocking the Keypad40
- Front Panel Buttons40
- Programming a Security Level41
Humidification42
- Installing the Humidity Module43
- Setting a Thermostat Jumper for Humidity Operation44
- Adjusting the Humidification Setpoint45
Dehumidification46
- Setting a Thermostat Jumper for Dehumidification Operation47
- Adjusting the Dehumidification Setpoint48
- Using Your Air Conditioner to Dehumidify49
- Using the Dehum Terminal50
Viewing Equipment Run-Times51
- Viewing the Override Operation Run-Time52
- Viewing the Humidification Run-Time53
- Viewing the UV Light Run-Time54
Electric Heat and Heat Pump Operation55
- Viewing the Heat Pump and Reversing Valve Jumper Settings56
- Viewing the Electric Heat Jumper Setting57
- Using Emergency Heat58
Timers and Deadbands59
- Adjusting the Heat/Cool Differential60
- Adjusting the Cycles Per Hour61
- Adjusting the Deadband62
- Adjusting the Minutes of Run-Time64
- Before the Next Stage64
- Selecting 2Nd Stage Turn65
- Off Temperature65
- How to Use the Energy Save Feature66
Energy Save Operation66
- Programming Run-Time Alerts67
- How to Set and Reset the Service Filter (Fan Run-Time) Alert68
- How to Set and Reset the UV Light Run-Time Alert69
- How to Set and Reset the Humidifier70
- Run-Time Alert70
Programming the Holiday Mode71
Overriding the Holiday Mode72
Configuring the MISC Outputs73
- Configuring the Jumpers74
- Hum Jumper Setting75
- W3 Jumper Setting75
- Explanation of Jumper Settings75
- Dehum Jumper Setting76
- Y2 Jumper Setting77
Factory Defaults, Calibration, and Sensors78
- Resetting the Thermostat to the Factory Default Settings79
- Calibrating the Temperature and Humidity Sensors80
Accessories81
- Advanced Setup Table82
- Index83

Carrier 33CS420-01 - Section 18 Factory Defaults, Calibration, and Sensors; Resetting to Factory Default Settings; Calibrating Temperature and Humidity Sensors

Table of Contents

Other manuals for Carrier 33CS420-01

Related product manuals