53
m. Press B(Down Arrow) once to display the
following --
1-25 Motor Nominal Speed
1740rpm
n. Press OK to highlight the rpm value a nd the n
use the Y and B (Up and Down Arrow)keys
to select the nameplate rpm. Press OK again to
set the selected rpm.
6. Entering Parameters for 1--71, 1--73, 1--82, and 1--90:
a. Press the Menu key to move the B(triangle
icon) so it is positioned ove r Main Menu. The
display show the following --
0 --- * * O p e r a t i o n / D i s p l a y
1---** L oad and Motor
b. Press B(Down Arrow) once to highlight the
bottom row.
c. Press OK, the display changes to --
1--- 0* General Settings
1---1* Motor Selection
d. Press B(Down Arrow) until the followin g display
appear s --
1--- 6* Load Depen. Setting
1--- 7* Start Adjustments
e. Press OK, the following display appears --
1-71 Start Delay
2.0s
f. Press OK to highlight t he num ber and then use
the Y and B (Up and Down Arrow)keysto
select the num ber provided in Table 17. Press
OK again to set the selected value.
g. Press B(Down Arrow) twice, the followin g
display appears --
1-73 Flying Start
[1] Enabled
h. Press OK to highlight the number in the bracket
andthenusetheY and B (Up and Down Ar-
row) keys to select the number provided in Table
17. Press OK again to set the selected value.
i. Press the Back key once, the following display
appears --
1--- 6* Load Depen. Setting
1--- 7* Start Adjustments
j. Press B(Down Arrow) once, the follow in g
display appears --
1--- 7* Start Adjustments
1 --- 8 * S t o p A d j u s t m e n t s
k. Press OK, the following display appears --
1-80 Function at Stop
[0] Coast
l. Press B(Down Arrow) once, the follow in g
display appears --
1-82 Min Speed for Functio…
1.0 Hz
m. Press OK to highl ight the number and then use
the Y and B (Up and Down Arrow)keysto
selec t the num ber provided in Table 17. Press
OK again to set the selected value.
n. Press the Back ke y once , the fol lowing display
appears --
1--- 7* Start Adjustments
1 --- 8 * S t o p A d j u s t m e n t s
o. Press B(Down Arrow) once, the followin g
display appears --
1 --- 8 * S t o p A d j u s t m e n t s
1--- 9* Motor Temperature
p. Press OK, the following display appears --
1-90 Motor Thermal Prote…
[4] ETR trip 1
q. Press OK to highlight the number in the bracket
then use the Y and B (Up and Down Arrow)
keys to select the number provided in Table 17.
Press OK again to set the selected value.
7. Setting References:
a. Press the Menu key to move the B(triangle
icon) so it is positioned ove r Main Menu. The
display show the following --
0 --- * * O p e r a t i o n / D i s p l a y
1---** L oad and Motor
b. Press B(Down Arrow) three times, the followin g
display appears --
2 --- * * B r a k e s
3---** Reference / Ramps
c. Press OK, the following display appears --
3--- 0* Reference Limits
3 --- 1 * R e f e r e n c e s
d. Press OK again, the following display appe ars --
3-02 Minimum Reference
0.000
NOTE: If the bottom row displays a number other than
0.000, press OK and use the Y and B (Up and Down
Arrow) key to select 0.000.
e. Press B(Down Arrow) once, the following dis-
play appears --
3-03 Maximum Reference
60.000
NOTE: If the bottom row displays a number other than
60.000, press OK and use the Y and B (Up and Down
Arrow) key to select 60.000.
To Next Page
Loading...
