EasyManua.ls Logo

Carrier Xpower Series - Branch pipes for indoor unit; Pipe selection examples

Carrier Xpower Series
29 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
15
Installation manual
5.6 Branch pipes for indoor unit
Based on Tab.5-7 and Tab.5-8, select the multi connection pipes
for the outdoor unit. Before installation, read the installation
manual for Outdoor Unit branch joints.
Unit: mm
Table.5-7 Outdoor unit multi-connective pipe assembly (Illustration)
Main pipe
g1, g2:
8~12HP: Φ25.4/Φ12.7;
14~22HP: Φ31.8/Φ15.9
L:
BJC-02-CM (i)
L+M:
BJC-03-CM(i)
L+M+N:
BJC-04-CM(i)
g1, g2, g3:
8~12HP: Φ25.4/Φ12.7;
14~22HP: Φ31.8/Φ15.9;
G1: Φ38.1/Φ19.1
g1, g2, g3, g4:
8~12HP: Φ25.4/Φ12.7;
14~22HP: Φ31.8/Φ15.9;
G1: Φ38.1/Φ19.1;
G2: Φ41.2/Φ22.2
5.7 Example
Liquid side
Gas side
Liquid side
Gas side
Indoor unit
capacity
A(×100W)
A45
A56
Φ12.7 Φ6.4
Φ15.9 Φ9.5 Φ19.1
Φ12.7
Φ15.9 Φ9.5
Table.5-9
Illustration
Outdoor
unit Qty.
2 units
3 units
4 units
Main pipe
Table.5-8 Outdoor unit multi-connective pipe assembly
Outdoor
unit Qty.
2 units
3 units
4 units
Outdoor unit connective
pipe diameter
Parallel connect
with the branch
joint assembly
Refer to
Table. 5-4
or 5-5 for
main
pipe’s
dimensions
Note: The pipe assemblies in the above table are special to this
model and must be purchased separately.
Take (22+12+12) HP with three modules as an example to
clarify pipe selection.
Take Fig.5-4 as an example, where the equivalent length of all
pipes is larger than 90 m.
When the branch
joint’s length 10 m
When the branch
joint’s length10 m
1)
2)
L
g1 g2
L
M
g1 g2
G1
g3
Main pipe
L
M
N
G2
G1
g1 g2 g3 g4
Main pipe
The branch joint in the inside of the unit.
There are a~m branch joints in the inside of the unit. The
branch joint diameter should be selected as per Tab. 5-9.
Main pipe inside the unit (Refer to Table. 5-3)
The main pipe L4 with N2, N3 downstream indoor units has a
total capacity of 140+71=211l. Pipe L4 diameter is Φ19.1/Φ
9.5. So, select BJF-224-CM(i) for branch joint D.
The main pipe L3 with N1~N3 downstream indoor units has a
total capacity of 140×2+71=351. Pipe L3 diameter is Φ28.6/ Φ
12.7. So, select BJF-710-CM(i) for branch joint C.
The main pipe L6 with N5, N6 downstream indoor units has a
total capacity is 140+28=168. Pipe L4 diameter is Φ19.1/Φ 9.5.
So, select BJF-224-CM(i) for branch joint F.
The main pipe L5 with N4~N6 downstream indoor units has a
total capacity of 140×2+28=308. Pipe L5 diameter is Φ22.2/ Φ
9.5. So, select BJF-330-CM(i) for branch joint E.
The main pipe L2 with N1~N6 downstream indoor units has a
total capacity of 140×4+71+28=659. Pipe L2 diameter is Φ
28.6/Φ15.9. So, select BJF-710-CM(i) for branch joint B.
A
B
1)
2)
3)
4)
5)
The main pipe L10 with N9, N10 downstream indoor units has
a total capacity of 71+28=99. Pipe L10 diameter is Φ15.9/Φ
9.5. So, select BJF-224-CM(i) for branch joint J.
The main pipe L9 with N8~N10 downstream indoor units has a
total capacity of 140+71+28=239. Pipe L9 diameter is Φ
22.2/Φ9.5. So, select BJF-330-CM(i) for branch joint I.
The main pipe L8 with N7~N10 downstream indoor units has a
total capacity of 140X2+71+28=379. Pipe L8 diameter is Φ
28.6/Φ12.7. So, select BJF-710-CM(i) for branch joint H.
The main pipe L12 with N12, N13 downstream indoor units
has a total capacity of 56×2=112. Pipe L12 diameter is Φ
15.9/Φ9.5. So, select BJF-224-CM(i) for branch joint L.
The main pipe L11 with N11~N13 downstream indoor units has
a total capacity of 140+56×2252. Pipe L11 diameter is Φ
22.2/Φ9.5. So, select BJF-330-CM(i) for branch joint K.
The main pipe L7 with N7~N13 downstream indoor units has a
total capacity of 140×3+71+56×2+28631, the pipe L7
diameter is Φ
28.6/Φ15.9. So, select BJF-710-CM(i) for branch
joint G.
The branch joint A with N1~N13 downstream indoor units has
a total capacity of 140×7+71×2+56×2+28×21290. So, select
BJF-1344-CM(i) for branch joint A.
Example: parallel connection of three outdoor units 12+12+22
(total capacity 46 HP). The total capacity of the indoor units is
1,290, if the equivalent length of all pipes is 90 m. According
to Tab.5-5, the main pipe’s diameter is Φ38.1/Φ22.2. The
master unit’s diameter is Φ38.1/Φ19.1 based on Tab.5-3.
Select the largest. The main pipe’s diameter is Φ38.1/Φ22.2
6)
7)
8)
9)
10)
11)
12)
C

Table of Contents

Related product manuals