Why power does not turn on in my Casio XJ-V1?
If the AC power cord of your Casio Projector is not connected correctly, ensure it is properly connected. If some type of error has occurred, consult 'Error Indicators and Warning Messages'.
How to fix blurry text on Casio Projector?
If the text is blurry on your Casio Projector, adjust the image focus. If the input source is an RGB signal, press the [AUTO] key to execute an automatic adjustment operation.
Why image color or display is very abnormal on Casio Projector?
If the image color or display is very abnormal on your Casio Projector, on the setup menu, select “Auto” for the “Input Settings J COMPUTER Terminal” setting.
How to resolve strange color on Casio XJ-V1 Projector?
To address strange color issues with your Casio Projector, try the following: Press the [FUNC] key and then select “Brightness” to adjust image brightness. Press the [FUNC] key and then select “Color Mode” to change the color mode. On the setup menu, use “Image Adjustment 1 J Color Balance” to adjust the projection image color balance.
What to do if the remote controller does not work with my Casio Projector?
If the remote controller of your Casio Projector is not working, try replacing the batteries. Also, make sure the remote controller is within about five meters from the projector when performing operations.
What to do if no image is projected on Casio XJ-V1?
If no image is projected or the projected image is abnormal on your Casio Projector, make sure the connected computer or video device is turned on and outputting a video signal. Also, select the correct input source on the projector that corresponds to the connected device.
How to fix internal temperature too high on Casio XJ-V1?
If the internal temperature of your Casio Projector is too high, check for any blocking of the projector’s intake vents and exhaust vents, and make sure that there is sufficient space around the projector. If there is dust accumulated around the intake vents and/or exhaust vents, turn off the projector and remove it.
What to do if internal temperature is too high and Casio XJ-V1 Projector turns off?
If the internal temperature of your Casio Projector is too high and the projector turns off, check for any blocking of the projector’s intake vents and exhaust vents, and make sure that there is sufficient space around the projector. If there is dust accumulated around the intake vents and/or exhaust vents, remove it. Confirm that the POWER/ STANDBY indicator is lit red (without flashing), and then turn power back on again. If the error occurs again when you turn power back on, contact your retailer or nearest authorized CASIO Service Center.
What to do if fan problem occurs and Casio XJ-V1 turns off?
If there is a problem with the fan and your Casio Projector turns off, confirm that the POWER/STANDBY indicator is lit red (without flashing) and that the fan has stopped. After checking the POWER/STANDBY indicator, disconnect the power cord from the projector and wait for all of the projector’s indicators to go out. Next, reconnect the power cord and turn projector power back on. If the error occurs again when you turn power back on, contact your retailer or nearest authorized CASIO Service Center.
Why power suddenly turns off and the Casio XJ-V1 restarts?
If the power suddenly turns off and the projector restarts, this normally does not indicate malfunction, so you can continue using the Casio Projector. However, malfunction may be indicated if successive restarts keep occurring. If this happens contact your original dealer or authorized CASIO service center.
Important safety and operational guidelines for projector setup and placement.
Operations related to adjusting the projected image quality and display.
Steps for navigating and operating the projector's setup menu.
Configuration options for image brightness, contrast, and color.
Details on various settings available within the setup menu.
Advanced image adjustments including frequency, phase, and overscan.
Adjustments for keystone correction, aspect ratio, and projection mode.
Guidelines and precautions for enabling and using the projector password.
Step-by-step instructions to modify the projector's password.
How to configure the projector to require a password at startup.
Explanation of the POWER/STANDBY and STATUS indicator lights.
Descriptions and actions for projector error codes and alerts.
Troubleshooting steps for when the projector fails to power on.
Resolution for password prompt errors and operational blocks.
Solutions for image projection issues or abnormal display.
Diagnosing issues indicated by red POWER/STANDBY and STATUS lights.
Actions for when the projector's light source fails to activate.
Guide for establishing a component video connection to the projector.
Procedure for updating the projector's firmware via USB.
Table detailing projector distance and screen size compatibility.
General| Matrix size | 0.55 \ |
|---|---|
| Number of colors | 1.073 billion colors |
| Native aspect ratio | - |
| Projection distance | - m |
| Projection technology | DLP |
| Contrast ratio (dynamic) | 20000:1 |
| Screen size compatibility | 30 - 300 \ |
| Projector native resolution | XGA (1024x768) |
| Keystone correction, vertical | -30 -30 ° |
| Focus | Manual |
| Offset | 72 % |
| Throw ratio | 1.54 - 1.71:1 |
| Optical zoom | 1.1 x |
| Focal length range | - mm |
| Light source type | Laser/LED hybrid |
| Service life of light source | 20000 h |
| Full HD | No |
| Supported graphics resolutions | 1200 x 1600, 1680 x 1056 |
| AC (power) in | Yes |
| Composite video in | 0 |
| USB connector type | Micro-USB B |
| Serial interface type | RS-232 |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| Noise level | 37 dB |
| Noise level (economic mode) | 35 dB |
| Placement | Desktop |
| Product type | Standard throw projector |
| Product color | White |
| Power source | AC |
| Power consumption (standby) | 0.23 W |
| Power consumption (typical) | 150 W |
| Operating temperature (T-T) | 5 - 35 °C |
| Remote control type | IR |
Weight and Dimensions| Width | 270 mm |
|---|---|
| Height | 89 mm |
| Weight | 2800 g |
To Next Page
