CASTLE Serenity - Setting The Weekly Schedule

Check for parts online at www.castlestoves.com or call 800-450-EDGE (3343) M-F 8-5
26
Operator's Manual
Serenity Pellet Stove
SET WEEKLY
Sun. Weekly Set
1: 1:15~ 7:00 67°F Yes
2: 17:00~23:45 72°F Yes
3: --:--~--:-- --°F No
4: --:--~--:-- --°F No
5: --:--~--:-- --°F No
Next All
Figure 23
SET CLOCK
10:45 Fri. May 20, 2011
Figure 24
NOTE: Along with the “Next” option on the screen,
there is also an “All “Option. After you have set
a particular time for a day, if you wish to set that
time for every day of the week, scroll down to
“Next” and press ENTER. Press the SCROLL DOWN
key to select and highlight “All.” Pressing ENTER
will then select that scheduled time and apply it to
each day of the week.
TIP: If at any point you need to leave the weekly
schedule screen or once you have nished with
setting all of your times, select the EXIT button
to return to the previous menu.
8. Once you’ve nished setting your schedule, without any
of the options highlighted, press the EXIT button. This
will save your schedule.
9. With a schedule set, make sure that the main display
screen on the controller reads ‘WEEKLY” (for operating
in the Weekly Mode) and that the unit is turned on. The
schedule will not take eect unless the unit is turned on
in the Weekly Mode. (See button 13 on Figure 19.)
Setting Other Data On Your Controller
Setting The Time And Date
1. Press and hold the ENTER button. This will take you to the
“SET DATA” screen.
2. Press ENTER again to enter the “SET CLOCK” screen. SEE
FIGURE 24.
3. To change the hour, press ENTER. This will highlight the
hour. Use your SCROLL UP and SCROLL DOWN buttons
to choose the appropriate time. Press ENTER to select the
correct hour, and then press ENTER a second time to begin
setting the minutes.
4. Continue this process for selecting and setting the day, month,
date and year.
5. When nished, and with nothing highlighted on the screen,
press the EXIT button.
2. In the “WEEKLY SCHEDULE” screen, you can begin with
setting the operation times for Sunday. Press ENTER to
highlight the hour and use the SCROLL UP and SCROLL
DOWN buttons until you reach your desired hour of
start time. Press ENTER again to highlight the minutes
and use SCROLL UP and SCROLL DOWN until you’ve
reached your desired minute of start. SEE FIGURE 23.
NOTE: Your Serenity controller uses military time to set
your weekly schedule.
3. Pressing ENTER again will allow you to set the stop time
of your stove. Use the same procedure for setting your
stove’s start time for selecting when you would like the
stove to stop. Once you’ve selected the stop time, press
ENTER.
4. Next you will have the opportunity to set the desired
temperature. Use the SCROLL UP or SCROLL DOWN
keys until you’ve reached the appropriate temperature
for the times you have selected. Press ENTER.
5. “Yes” will now be highlighted. If you have set this
particular time correctly, press ENTER. This will take you
out of your rst set time.
If you wish to erase a scheduled time, use your ENTER
key to highlight “YES” on the screen for that scheduled
time. Select “No” using your SCROLL UP or SCROLL
DOWN key. With “No” highlighted, press ENTER to erase
the data.
6. To set another time for that particular day, press
SCROLL DOWN and continue by repeating steps 2-5 as
appropriate.
NOTE: You must set your times in chronological order.
The rst schedule slot of one day MUST be earlier
in the day than the second schedule slot on your
weekly schedule list, etc.
7. Once you have set all times for Sunday, SCROLL DOWN
to “NEXT”. Pressing ENTER once will highlight “NEXT”.
Pressing ENTER again will take you to the following day.
Proceed with setting a schedule for the rest of the week
using the preceding instructions.