What to do if alarm is active against water overflow in CDA WC140 Dishwasher?
If the alarm is active against water overflow in your CDA dishwasher, turn off the dishwasher and disconnect the water supply. Contact CDA service.
How to fix inadequate water supply to my CDA WC140?
To fix an inadequate water supply to your CDA dishwasher: ensure the water inlet tap is fully open, close the water tap, separate the water inlet hose from the tap, and clean the filter. Restart your machine. If the error continues, contact CDA service.
How to prevent rust stains on dishes in CDA WC140?
Rust stains on dishes in your CDA dishwasher can occur if different sets of cutlery are mixed. Also, the water softener setting may be too high, the salt compartment cap might not be completely closed, or there could be a poor appliance earth. Separate your cutlery sets, adjust the water softener, ensure the cap is sealed, and check the mains electrical supply.
What to do if my CDA WC140 programme will not start?
If your CDA dishwasher programme won't start, check if the water tap is turned off, ensure the dishwasher door is fully closed, and inspect the water inlet filter and machine filters for blockages. Also, check the plug, fuse, and circuit breakers of the mains supply.
What causes rust stains on dishes in my CDA Dishwasher?
Rust stains on dishes from your CDA dishwasher can be caused by keeping different sets of cutlery together, too much salt because the water softener setting is too high, the salt compartment cap not being completely closed, or a poor appliance earth. Check the mains electrical supply.
Why does my CDA WC140 Dishwasher stop mid cycle?
Your CDA dishwasher might stop mid-cycle due to a power failure, water inlet failure, or because the programme is on standby. Check these possible causes.
What to do if my CDA WC140 leaves dishes wet?
If your CDA dishwasher leaves dishes wet, it might be because a programme without a drying stage was selected, the rinse aid setting is too low, or dishes were unloaded too soon. Allow more time for drying or adjust the rinse aid setting.
What causes white stains on dishes in my CDA Dishwasher?
White stains on dishes from your CDA dishwasher can be due to insufficient detergent, a rinse aid setting that's too low, not enough dishwasher salt, a water softener setting that's too low, or the salt compartment cap not being completely closed. Check these to resolve the issue.
Why is my CDA Dishwasher wash performance so low?
Low wash performance in your CDA dishwasher can occur due to several reasons: dishes not loaded properly, not enough detergent, incorrect wash program, blocked spray arm, clogged or incorrectly fitted filters or a blocked water drain pump. Please check these aspects to improve performance.
What to do if the door of my CDA WC140 is not opening or closing properly?
If the door of your CDA dishwasher isn't opening or closing correctly, it might be due to the door tension not being properly adjusted for the decor door. You should adjust the door tension.
General| Door color | Not applicable |
|---|---|
| Display type | LED |
| Appliance placement | Fully built-in |
| Control panel color | Stainless steel |
| Drying class | B |
| Washing class | A |
| Noise level | 52 dB |
| Number of place settings | 12 place settings |
| Number of washing programs | 5 |
| Water consumption per cycle | 15 L |
| Energy consumption per cycle | 1.05 kWh |
Weight and Dimensions| Depth | 570 mm |
|---|---|
| Width | 596 mm |
| Height | 875 mm |
Using the test strip to determine water hardness level.
Procedure to adjust the softener setting via the control panel.
How to adjust rinse aid levels for optimal drying and stain removal.
How to clean door seals and the essential filter components.
Codes for inadequate water supply and continual fill issues.
Codes for waste water discharge, heater, and overheating faults.
Codes for faulty electronic cards and water overflow alarms.
Resolving problems with programmes not starting or stopping mid-cycle.
Addressing low wash quality, white stains, and rust marks.
Troubleshooting inadequate drying and door opening/closing faults.
Instructions for fuse changes and connecting alternative plugs.
Connecting water inlet and drain hoses, checking for leaks.
To Next Page
