Why is my cecotec Conga 1690 not cleaning efficiently?
If your Cecotec Vacuum Cleaner isn't cleaning efficiently or you notice dust leaking, the dust tank might be full. Empty it and also check the high-efficiency filter for blockages; clear it if needed. Another possible cause is that the main brush is tangled. If so, please clear it up.
How to fix connection failed between phone and cecotec Conga 1690?
If the connection between your mobile phone and the Cecotec Vacuum Cleaner robot failed, ensure that both the robot and its charging base are in an area with a strong Wi-Fi signal. If the problem persists, try resetting your router and attempting the connection again.
Why is my cecotec Conga 1690 always offline?
If your Cecotec Vacuum Cleaner robot is always offline, ensure it is successfully connected to your network. Also, make sure it remains within the range of your Wi-Fi signal at all times.
What to do if my Cecotec Vacuum Cleaner does not start?
If your Cecotec Vacuum Cleaner robot is not starting up or cleaning, allow it to charge fully before using it. Also, make sure that you operate the robot in a room where the temperature is within the recommended range.
How to stop strange noise during cleaning with cecotec Conga 1690 Vacuum Cleaner?
If your Cecotec Vacuum Cleaner robot emits a strange noise during cleaning, it might be due to foreign objects tangled in the main brush, side brush, or omnidirectional wheel. Stop the robot and clear any obstructions.
Why can't my cecotec Conga 1690 Vacuum Cleaner connect to Wi-Fi?
If your Cecotec Vacuum Cleaner robot could not connect to Wi-Fi, the Wi-Fi signal may be weak. Ensure the Wi-Fi signal is strong enough. If the connection is unstable, reset your router, check for app updates, and try again.
Why does my Cecotec Vacuum Cleaner not resume cleaning?
If your Cecotec Vacuum Cleaner robot does not resume cleaning, it may be because the robot is not in Night mode. It will not resume cleaning under this mode. Also, the robot won’t resume cleaning if you manually place it on the charging base.
What to do if cecotec Conga 1690 Vacuum Cleaner did not carry out the scheduled cleaning?
If your Cecotec Vacuum Cleaner robot did not carry out the scheduled cleaning, it might be in Night mode. Switch mode. Also, ensure that the robot is connected to the network.
What to do if cecotec Conga 1690 does not work properly?
If the Cecotec Vacuum Cleaner robot does not work properly, turn it off, switch it off, and then turn it back on again.
What to do if my cecotec Conga 1690 cannot return to the charging base?
If your Cecotec Vacuum Cleaner robot cannot charge or return to its charging base, try these steps: First, relocate the charging base to an area free of obstacles. Clean the charging terminals and ensure the power switch is turned on. If the robot is too far from the base, place it closer and try again. Finally, make sure the charging terminals are clean.
General| Model | Conga 1690 |
|---|---|
| Category | Robot Vacuum Cleaner |
| App Control | Yes |
| Mop Function | Yes |
| Filter Type | HEPA |
| Wi-Fi Connectivity | Yes |
| Wet Mopping | Yes |
| Auto Recharge | Yes |
| Scheduling | Yes |
| Color | Black |
| Battery Type | Li-Ion |
| Control | App |
| Voice Control | Amazon Alexa, Google Assistant |
| Operating Modes | Auto, Edge, Manual |
| Programmable | Yes |
| Sensors | Anti-fall |
| Virtual Walls | Yes |
Instructions for setting up the robot and charging base, including required clearances.
Steps for correctly installing the wet and dry tank onto the robot.
Details the function of physical buttons on the robot for control.
Explains the most common cleaning mode for full house coverage.
How to activate the mode for the robot to return to its charging base.
Description of all buttons and their functions on the remote control.
Guide to setting the current time and scheduling cleaning sessions.
Introduction to the various cleaning modes available for the robot.
How to use the mode that cleans along the edges of rooms.
Instructions for cleaning a specific 2x2 meter area.
Details the mode where the robot cleans randomly.
Instructions for cleaning using gyro navigation.
How to perform two consecutive cleaning cycles.
Detailed instructions for the robot's scrubbing function and water intensity.
Instructions for manually controlling the robot's movement.
Highlights the benefits and features of using the Conga 1690 App.
Instructions for downloading the app and connecting the robot.
Guide to cleaning and maintaining the main brush and its compartment.
Instructions for emptying and cleaning the dust tank.
Instructions for cleaning and replacing the high-efficiency filter.
Guide to cleaning and recommended replacement of side brushes.
Instructions for cleaning the robot's free-fall sensors.
Common problems and their solutions for robot operation and connectivity.
To Next Page