What to do if my Celleration Ultramist system will not turn on?
If your Celleration Medical Equipment system isn't turning on, make sure the power cord is properly plugged into both the generator outlet on the back of the instrument and the power outlet. Also, verify that the power outlet is delivering power. If the issue persists, contact Celleration Customer Service, as the fuse on the system may be missing or blown.
What to do if no saline is coming out of the Celleration Ultramist applicator?
If no saline or insufficient saline is coming out of the Celleration Medical Equipment applicator, ensure that the 'wound ready' screen is visible on the display. Check that the treatment on/off button has been pressed to begin the treatment. Make sure the saline pump door is closed and the tubing is properly loaded in the saline pump using the tubing guides. Also, verify that the tubing is not clamped, kinked, or knotted. Finally, ensure the treatment wand tip is correctly aligned in the center of the applicator and that the tubing spike is fully mated with the saline bag.
What to do if my Celleration Ultramist Medical Equipment treatment wand has no power?
If there is no power to the treatment wand of your Celleration Medical Equipment (and no screen display), first ensure that the system is turned on using the power switch located on the back of the system. Also, verify that the treatment wand cable is securely inserted into the connector on the generator.
What does it mean if my Celleration Ultramist Medical Equipment says 'Overheat'?
The 'Overheat' alarm on your Celleration Medical Equipment indicates that the ultrasound is being turned off as a preventive measure because the treatment wand temperature has exceeded the allowed limit. This does not necessarily indicate a malfunction. The system will begin a cool-down process, counting down the minutes required to cool the system. Do not turn off the system during this cool-down period, as it could require a replacement of the applicator. Once the cool-down is complete, the 'paused treatment' screen will appear, and you can resume the treatment. Note that 20 minutes is the expected maximum treatment time after periods of system inactivity.
What to do if saline is leaking around the Celleration Medical Equipment applicator?
If you notice saline leaking around the applicator of your Celleration Medical Equipment, ensure that the treatment wand tip is properly aligned in the center of the applicator. Also, if the treatment wand position during treatment caused saline to accumulate inside the applicator, turn the applicator tip downward to allow excess saline to drain and then continue treatment.
What does it mean if I see an error message on my Celleration Medical Equipment display screen?
If you see an error message on the display screen of your Celleration Medical Equipment, refer to the common errors table to determine the appropriate action. If the error continues, note the contents of the error message and call Celleration Customer Service.
What to do if all keys on the Celleration Ultramist keypad are not functioning?
If all the keys on your Celleration Medical Equipment keypad are not functioning, shut down the system by turning off the power and then restarting it. If the error continues, call Celleration Customer Service, as this may indicate a system software error.
What to do if my Celleration Medical Equipment applicator is damaged?
If your Celleration Medical Equipment applicator is damaged, replace it with a new applicator. The damage might have occurred during shipment.
What to do if a single key on the Celleration Ultramist Medical Equipment keypad is not functioning?
If a single key on the keypad of your Celleration Medical Equipment is not functioning, call Celleration Customer Service, as this may indicate a mechanical failure.
What to do if the sterile Celleration Medical Equipment applicator package is open or damaged?
If the sterile applicator package for your Celleration Medical Equipment is open or damaged, replace it with a new applicator, as the damage might have occurred during shipment.
Lists common error messages and their causes on the display screen.
Explains the meaning of the indicator lights on the generator.
Troubleshooting steps for when the system fails to power on.
Solutions for issues where the treatment wand shows no display or power.
Addresses problems with individual or all keypad keys not responding.
Information and solutions for the system's overheat alarm.
General guidance for interpreting and resolving display error messages.
Troubleshooting steps for issues with saline flow from the applicator.
Solutions for problems causing saline leaks around the applicator.
Guidance on handling situations where the applicator is damaged.
Instructions for dealing with damaged sterile packaging of applicators.
Important safety warnings regarding device operation and handling.
Precautions to ensure treatment effectiveness and proper device use.
Technical specifications of the UltraMIST system, including safety and performance data.
Contact information for technical support and customer service.
Overview of commonly used controls and their functions.
Definitions and explanations of symbols used throughout the manual.
Declaration regarding the system's electronic emissions and compliance with standards.
Declaration regarding the system's radiation emissions and safety.
General| Frequency | 40 kHz |
|---|---|
| Portability | Portable |
| Application | Wound care |
| Technology | Low-frequency ultrasound |
| Power Source | AC adapter |
To Next Page